Question about 2007 Mazda MAZDA5

Open Question

How to replace brake pads on a Mazda 5 - 2007 Mazda MAZDA5

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: change rear brake pads on mazda 323f 2l v6 1997

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

  • 726 Answers

SOURCE: brake pads replacement on mazda protege 5 2002

no it will push back u can undo the nozzile if u want to make it easy so the fluid comes out or by a camp wind up one and do it that way like machanics

Posted on Jul 18, 2008

carsandcomps
  • 722 Answers

SOURCE: 2005 MAZDA 6 BRAKE PADS

Since you are taking it back, have them check all the brake lines in front, and the wheel cylinder (if the back has drum breaks). Although you had only the front done, it's a good ideas to have them check the back brakes, and the master cylinder. Check your brake fluid before taking it back and make sure it's full, if so, you may just have air in the brake lines. If this is the case, either they forgot to bleed the brakes, or didn't bleed them enough.

Posted on Apr 01, 2009

  • 3 Answers

SOURCE: BRAKES ON FRONT 2002 PROTEGE 5 MAZDA

When I change my front brakes, I use a "C" clamp to slowly push the piston back in. (You can get them for a few dollars at Wal-Mart, etc.) Make sure you open the brake fluid reservoir while compressing them, as the fluid level will rise; but don't leave the reservoir open too long, as brake fluid will absorb water from the air.
For the parking brake, I'm not sure. I think the parking brake often works off of the rear brakes, so changing the pads should have helped there. Maybe air in the lines? Do you have any trouble with "soft" or "mushy" brakes when you use them? If so, you might want to bleed the system, to get any air out - it can be dangerous.

Posted on May 16, 2009

Biggdex35
  • 333 Answers

SOURCE: mazda miata 2003 replaced rear brake pads now

Doe's the back brakes work? Is number 7 and 15 hooked up right? If they are. Try backing up and hitting brakes, This will tigjhten them up.
1 – SUPPORT PLATE
2 – RETURN SPRING
3 – ANCHOR PLATE
4 – RETURN SPRING
5 – CABLE GUIDE
6 – PARKING BRAKE LEVER
7 – ADJUSTER CABLE AND SPRING
8 – SHOE RETAINER, SPRING AND PIN
9 – SECONDARY SHOE AND LINING
10 – LEVER SPRING
11 – ADJUSTER LEVER
12 – ADJUSTER SCREW ASSEMBLY
13 – SHOE SPRING
14 – PRIMARY SHOE AND LINING
15 – PARKING BRAKE STRUT AND SPRING e753404.png

Posted on May 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a mazda xedos 6 front brake pads?


Hi,
Brake Pads are an important part of your Mazda6's braking system. They are the replaceable friction pads that pinch the brake disc or drum when the brakes are applied. You should replace the brake pads before they wear beyond a quarter inch or risk damaging your Mazda6's brake discs.

Instructions
Remove the old Brake Pads
  1. Step 1 Park your car on a level surface. If you have a stick shift car, make sure the car is in gear. Do not set the parking brake. Place blocks in front of the front tires so the car does not move while you are working on it.
  2. Step 2 Open the hood of your car. Locate the master cylinder and brake fluid container. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.
  3. Step 3 Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.
  4. Step 4 Disconnect the parking brake cable from the brake caliper. The cable is usually held in place with a retaining clip. You can use pliers to remove the clip and disconnect the cable.
  5. Step 5 Remove the upper caliper bolt. Rotate the caliper downward until you can comfortably work on it. Remove the springs, pads and shims from the caliper.

    Install the new Brake Pads
  6. Step 1 Use the recommended tool to press the caliper piston back into the piston assembly.
  7. Step 2 Insert the shims, springs and new pads into the caliper. Reconnect the parking brake cable.
  8. Step 3 Rotate the caliper upward and back into place. Use the socket wrench to tighten the upper mounting bolt to 27 to 36 foot lb. (37 to 49 Nm) if you have a Mazda6 or to 16 to 23 foot lb. (21 to 31 Nm) if you have a Mazdaspeed6.
  9. Step 4 Replace the tire wheel assembly. Lower the car to the ground.
  10. Step 5 Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.
  11. Step 6 Season the brake pads by making only gentle stops when you are driving for the first week after you install the new brake pads. Try not to do any hard stopping when you are seasoning the brakes.
Take care

Jul 23, 2010 | 2004 Mazda 6

1 Answer

Mazda miata 2003 replaced rear brake pads now parking brake does not work any ideas?


Doe's the back brakes work? Is number 7 and 15 hooked up right? If they are. Try backing up and hitting brakes, This will tigjhten them up.
1 – SUPPORT PLATE
2 – RETURN SPRING
3 – ANCHOR PLATE
4 – RETURN SPRING
5 – CABLE GUIDE
6 – PARKING BRAKE LEVER
7 – ADJUSTER CABLE AND SPRING
8 – SHOE RETAINER, SPRING AND PIN
9 – SECONDARY SHOE AND LINING
10 – LEVER SPRING
11 – ADJUSTER LEVER
12 – ADJUSTER SCREW ASSEMBLY
13 – SHOE SPRING
14 – PRIMARY SHOE AND LINING
15 – PARKING BRAKE STRUT AND SPRING e753404.png

May 24, 2010 | 2003 Mazda MX-5 Miata

1 Answer

1996 mazda b3000 rt front brake seems to not disengage enough. i have replaced caliper & brake line.


take the caliper off and check the brake pad slides to make sure the pads arent sticking and dragging. also check the wheel bearing to see if it is bad because it can cause the rotor to set at a slant and rub on the pads.

May 18, 2010 | Mazda B3000 Cars & Trucks

1 Answer

The handbrake doesn't work on my recently bought 1997 Mazda MX5. The garage (non Mazda specialist) says it needs new calapers, brake pads and discs. Is that right?


Maybe, but probably not. If all those things were messed up, you'd also have trouble with the brakes under normal driving conditions.

You don't need a Mazda mechanic to work on your brakes, but you should find another garage and at least get a second opinion.

Miata brakes are very easy to work on -- not much harder than changing a tire. If you're up for it, get a Chilton's or Haynes manual from your local library or auto parts place and dive in. It's straightforward to inspect them yourself, and even replace your own pads with simple tools.

Sep 23, 2009 | 1997 Mazda MX-5 Miata

1 Answer

How to install brake pads for mazda 6


Hi,

Brake Pads are an important part of your Mazda6's braking system. They are the replaceable friction pads that pinch the brake disc or drum when the brakes are applied. You should replace the brake pads before they wear beyond a quarter inch or risk damaging your Mazda6's brake discs.

Instructions

    Remove the old Brake Pads
  1. Step 1 Park your car on a level surface. If you have a stick shift car, make sure the car is in gear. Do not set the parking brake. Place blocks in front of the front tires so the car does not move while you are working on it.
  2. Step 2 Open the hood of your car. Locate the master cylinder and brake fluid container. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.
  3. Step 3 Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.
  4. Step 4 Disconnect the parking brake cable from the brake caliper. The cable is usually held in place with a retaining clip. You can use pliers to remove the clip and disconnect the cable.
  5. Step 5 Remove the upper caliper bolt. Rotate the caliper downward until you can comfortably work on it. Remove the springs, pads and shims from the caliper.
  6. Install the new Brake Pads
  7. Step 1 Use the recommended tool to press the caliper piston back into the piston assembly.
  8. Step 2 Insert the shims, springs and new pads into the caliper. Reconnect the parking brake cable.
  9. Step 3 Rotate the caliper upward and back into place. Use the socket wrench to tighten the upper mounting bolt to 27 to 36 foot lb. (37 to 49 Nm) if you have a Mazda6 or to 16 to 23 foot lb. (21 to 31 Nm) if you have a Mazdaspeed6.
  10. Step 4 Replace the tire wheel assembly. Lower the car to the ground.
  11. Step 5 Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.
  12. Step 6 Season the brake pads by making only gentle stops when you are driving for the first week after you install the new brake pads. Try not to do any hard stopping when you are seasoning the brakes.
Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Sep 20, 2009 | 2004 Mazda 6

1 Answer

I'm trying to replace my front pads there are 2


Replace left and right brake pads at the same time. Do not replace brake pads for one side of the vehicle only.
  1. Raise and support front of vehicle.
  2. Remove tire and wheel assemblies.
  3. Remove pad pins and springs.
  4. Remove brake pads, then shims.
  5. Reverse procedure to install. When installing new brake pads, push caliper piston inward using piston compressor No. 490221600C or equivalent.

nothing Special that I see

Jul 14, 2009 | Mazda 323 Cars & Trucks

1 Answer

Brake Pad Replacement


Are you talking about the rear brakes? It's tricky because there is a bolt directly behind the piston that MUST be opened first. The gear inside, after opening that bolt, must be loosened with a hex key to retract the piston so that you can remove/replace the pads

May 02, 2009 | Mazda Protege Cars & Trucks

1 Answer

High pitched squeal when i step on the brakes


what is wrong is that is the warning signal that it is time for a change of brake pads and an inspection of brake shoes

Apr 21, 2009 | 2000 Mazda MX-5 Miata

1 Answer

BRAKES ON FRONT 2002 PROTEGE 5 MAZDA


When I change my front brakes, I use a "C" clamp to slowly push the piston back in. (You can get them for a few dollars at Wal-Mart, etc.) Make sure you open the brake fluid reservoir while compressing them, as the fluid level will rise; but don't leave the reservoir open too long, as brake fluid will absorb water from the air.
For the parking brake, I'm not sure. I think the parking brake often works off of the rear brakes, so changing the pads should have helped there. Maybe air in the lines? Do you have any trouble with "soft" or "mushy" brakes when you use them? If so, you might want to bleed the system, to get any air out - it can be dangerous.

Mar 21, 2009 | 2002 Mazda Protege

Not finding what you are looking for?
2007 Mazda MAZDA5 Logo

Related Topics:

1,086 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...