Question about 2004 Chevrolet TrailBlazer

1 Answer

2004 chevy trailblazer 4 wheel drive front axle lock nut torque setting

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 359 Answers

The torque spec is 103ft lbs. Most axle nuts on 4wd are around 100lbs, I have worked on cars for a while, so I usually tighten it down "wrist" tight, and give it a 1/4 turn. Always ends up being between 90-105lbs. Thanks.

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 Chevy Trailblazer anti lock breaks system is kicking in on dry pavement when slowing down to stop? The break peddle is pulsating upon stopping?


Usually a front speed sensor/wheel hub going bad. is there a humming noise from the front end area while driving at highway speeds? If there is, try to isolate which side it is, and have that hub bearing replaced and make darn sure the axle nut is torqued to the proper spec, or it will fail. To many auto techs just tighten them up withan impact gun, and say its good.

Aug 10, 2014 | Cars & Trucks

1 Answer

4-Wheel Drive


More than likely it is the switch alot of electric 4-wheel drive switches have been known to go bad from lack of use

Jan 26, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

2002 Chevy 4wd


maby im wrong but if you rev up and only rear wheels spin that means that it might be 4 wheel drive but not constant 4 wheel drive or diff lock system ,,,, ,, in 4 wheel drive all wheells will turn together but if pressure of slip is bad enough or torque high enough only 2 wheels will drive ,,, thats why diff lock locks wheels together in each axle to over come this ,,, all wheel drive like in landrover locks all 4 wheels together to ensure all wheels rotate to give best grip

Feb 13, 2012 | 2002 Chevrolet Suburban

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

Front bearing nut torque specification rear wheel drive?


front bearing wheel nut holding axle on? 115 foot pounds and hammer in or crimp the nut after tightening. ^ like shape into slot of axle this locks the axle. for the wheel bearing for rear wheel drive the nut should be tightened by hand till tight 15 foot pounds then backed off 1/4 turn, be sure there is plenty of grees in the bearing cup before tighting nut be sure to line up slot for key with rotor on the rotor should turn free and should not have any slop in it, put the wheel on it and put the nuts on and try wiggleing the wheel back and forth if any movement readuast nut. If it is to tight it will over heat outter wheel bearing, also be sure there is greese in inner wheel bearing.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

I have 2004 Trailblazer that has a high speed whine from the front end somewhere. Not the transmission. Could it be front axle or something?


could be wheel bearings..also make sure your 4 wheel drive is released all the way sometimes they get stuck

Mar 09, 2010 | 2004 Chevrolet TrailBlazer

4 Answers

Four-wheel drive will not work and is not transfer case, could be a fuse?


IT COULD BE A FUSE THERE ARE FUSES UNDER THE HOOD FOR 4 WHEEL DRIVE ALSO IF THAT DOED NOT WORK CHECK 4 WHEEL DRIVE SELINOID

Dec 13, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

I have a 2004 chevy silverado and the 4 wheel


the most likely cause is the front axle shift motor if bad your your front axle shaft will not lock in.if there is no shifting of transfer case there is also a electric motor that engages that in .

Oct 17, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

I am looking for the factory torque settings for the front wheel bearings for a 2004 Chevy s10 pick up.


IF YOU HAVE 4WD YOU WILL HAVE TO REPLACE BEARINGS.NOT ADJUSTABLE. IF YOU HAVE A 2WD YOU WILL REMOVE COTTER PIN AND LOOSEN THE SPINDLE NUT.SPIN THE WHEEL FORWARD BY HAND THE TORQUE NUT TO 12 FT LBS TO SEAT BEARING.THEN BACK OFF NUT 1/4 TO 1/2 TURN TO UNTIL HOLE IN SPINDLE LINE UP WITH SLOT IN NUT.THEN INSTALL A NEW COTTER PIN.

Sep 11, 2009 | 2004 Chevrolet S-10

Not finding what you are looking for?
2004 Chevrolet TrailBlazer Logo

1,186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...