Question about Volkswagen Golf

Open Question

Big end cap nuts torque setting 1.6 akl vw golf engine

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: golf iv 1.6 8v cylinder head torque settings

Hi the title says 1986 is the correct

Posted on Mar 06, 2011

Ad
  • 537 Answers

SOURCE: Volkswagen golf 1.4 8valve engine(AGY) Big end and main Bearing torque setting

Mains Stage 1-33Nm Stage 2- 65Nm
Big ends 30Nm

Posted on Sep 26, 2012

steve_e_uk
  • 1675 Answers

SOURCE: golf iv 1.6 8v cylinder head torque settings

hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the big ends torque settings for vw golf chico 1996 model


Which engine? The diesel and gas (petrol) engines will need different torque. All three gas engines appear to call for 22 foot-pounds plus 90 degrees with threads and bearing surfaces oiled.

Aug 04, 2014 | Cars & Trucks

1 Answer

I need the Wheel Nut Torque settings for a 2009 VW Golf Estate 1.9 TDI


The wheel bolts torque settings for a 2009 VW Golf Estate 1.9 TDI is 120 Nm.

May 31, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

2002 audi tt 225 bhp cranksharft torque settings


Crankshaft torque settings for 2002 Audi TT 225 BHP:

1. Main bearings: Renew bolts = Yes
2. Main bearings: Stage 1 = 65 Nm
3. Main bearings: Stage 2 = 90 degrees
4. Big end bearings: Renew bolts / nuts = Yes
5. Big end bearings: Stage 1 = 30 Nm
6. Big end bearings: Stage 2 = 90 degrees
7. Flywheel / driveplate = 60 Nm + 90 degrees (use new bolts / nuts)
8. Crankshaft pulley / damper centre bolt = 90 Nm + 90 degrees (use new bolts)


Nov 25, 2010 | Audi TT Cars & Trucks

2 Answers

Golf iv 1.6 8v cylinder head torque settings


hi to tighten you have to do it in 4 stages as follows
1st stage 40nm leave 5 mins 2nd stage 60nm leave 5 mins 3rd stage 90 degrees leave 10 mins 4th stage 90 degrees then you are done i will try put order on here i hope this works as follows
10 4 2 6 8 front of engine back of engine 7 5 1 3 9

in that order hope this helps

May 10, 2010 | 1986 Volkswagen Golf

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

1 Answer

How do i fix a driveshaft on a 1995 vw golf


take off the wheel.
remove the nut at the end of the axle.36mm socket or so.
on the lower control arm there is a castle nut with a cotter pin.take out the pin and remove the castle nut.
then with a pry bar,put pressure on the lower control arm so the ball joint is free out of the lower control arm. pull on and swing away the hub assembly until it clears the spline from the outer axle.swing the hub out of the way so the axle can be pulled out of the transmission.
tie it out of the way with a tie down cord.
using a prybar,separate the inner axle knuckle from the transmission.
there is a spring on the end of the inner spline,some are quite tight on there.
remove the axle.

installation is reverse of the above.
first the shaft is put into the transmission, then you will have to hammer it in until it "sets". use a soft material like wood on the end of the axle .do not hit the spline directly with a hammer,it will damage the splines!
make sure not to damage the transmission seal where the drive shaft goes into.you will lose a little transmission fluid and will have to top it up.once the shaft is installed,turn it and make sure it meshes proper inside the transmission. then move the hub into place over the driveshaft.tighten the axle shaft to vw torque spec.
install the lower ball joint into the control arm and tighten the castle nut to vw torque spec.and install a new cotter pin.
install the wheel nuts and torque to spec.
alot of heroes out there use a straight impact gun and that can bend rims,rotors and cause other problems.TORQUE them.they are 80lb ft for a reason, not 300 lb/ft like an air gun.a torque extension bar is perfect and an 80 lb stick is about 20 dollars.
it takes a special stick to measure the vw tranny fluid if it is an automatic.a dealer will be able to check it unless you want the vw special tool for that.
tools needed will be an impact gun,axle nut socket,torque wrench,socket set with 1/2 inch drive,36"pry bar,jack stands,and a trouble light .
it takes about half an hour to do if you do alot of them.
go slow do it right and it may take a couple hours,but you will feel good about it.

Sep 14, 2009 | 1995 Volkswagen Golf

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

550 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...