Question about Chevrolet S 10

1 Answer

My s10 chevy p/u has a leak on the evap canister, I need to know where is it located in the motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

Your evap. canister is large round plastic cylinder in engine compartment. (About the size of coffee can with 2 hoses coming from lid)

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

1 Answer

What do codes P0300, P0442, P0446 mean on a S10 chevy 2001


Code 300 is for a random miss which may be tough to track down.
Code 442 is for a small leak detected in the EVAP system and 446 is for a problem with the performance of that system. The EVAP system vents fumes from the gas tank to the vapor canister. Sometimes the small leak is the gas cap not being on tight, and sometimes it is a component or hose in the system.

Feb 07, 2014 | Chevrolet Cars & Trucks

1 Answer

P0455 code on 2006 Chevy 4WD 5.3 liter


Trouble Code: P0455

Evaporative Emission (EVAP) System Large Leak Detected

Possible Causes:


A fuel fill cap that is left OFF after a fuel fill will cause this DTC to set.A loose, missing, or damaged fuel fill cap can cause this DTC to set.A blockage or restriction in the EVAP purge solenoid, purge pipe EVAP canister, or vapor pipe, can cause this DTC to set.A temporary blockage in the EVAP purge solenoid, purge pipe, or EVAP canister could cause an intermittent condition. Inspect and repair any restriction in the EVAP system.To help locate intermittent leaks, use the J 41413-200 to introduce smoke into the EVAP system. Move all EVAP components while observing smoke with the J 41413-SPT .To improve the visibility of the smoke exiting the EVAP system, observe the suspected leak area from different angles with the J 41413-SPT .Observe the Freeze Frame/Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition occurs that caused the DTC to set . This may assist in diagnosing the condition.

Jan 30, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

2005 chevy malibu code p0466 how do I fix this


the EVAP canister is located under the car on the drivers side above the gas tank. that particular code could mean anything as far as the EVAP system goes. it could be anything to you overfilling your gas tank to your EVAP canister needing to be replaced to the small hose under the hood having a pin-sized hole in it. the most effective way to find the problem is to take it to an ASE certified shop or dealer and have them run a FULL scan of your system, if you havent already. about the only way to find a small leak is to have a mechanic run smoke though the EVAP system.

Nov 14, 2011 | 2005 Chevrolet Malibu

1 Answer

Where is the evap canister located on a 1997 chevy s10 blazer


The canaster it self is located on the drivers side rear of the wheel near the bumper has three hoses connecting to it 1 goes to the rollover valve on the fuell tank 1 to the canister vent solenoid on the member over the spare tire and the other 1 to the canister purge solenoid located on the mid left side of the intake manifold . What codes do you get ?

Jan 28, 2011 | 1997 Chevrolet Blazer

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Were is the evap located on 2001 Chevy s-10 blazer with v6


The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.

47e8f38.jpg

Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve


4d7b3e9.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).

Mar 26, 2010 | 2001 Chevrolet Blazer

1 Answer

Code p1457 EVAP control leak for a 2000 Acura TL


i have not seen a evap canister need to be replaced . i belive it is located near the fule tank . the proublem is most likly the evap control valve or a leak . i use a smoke machine to locate leaks

Jun 04, 2009 | 1999 Acura TL

1 Answer

Trying to locate evap valve on 2004 chevy s10


on the drivers side behind the gas tank under the truck bed.

Feb 01, 2009 | 2004 Chevrolet S-10

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

442 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...