Question about 1991 Nissan 300ZX

1 Answer

Problems whit the knock sensor - 1991 Nissan 300ZX

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

Replace it. they all go bad at some point and ****** timing on all nissan 91 up. its a paint to change under the manifold and around $250 new. you can bypass it by putting a 400ohm resistor inline out to ecu and the car will start up good always and run great with good gas milage. beware if you ping run bad gas or preignite it wont correspond to safety and hurt your engine. so run 93 octane like you should be in the first place with that car and youll be fine

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i deal with Error Code P0328


the following information courtesy of OBD-CODES.com P0328 Knock Sensor Circuit High Input OBD-II Trouble Code Technical Description Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) What does that mean? Knock sensors are used to detect engine pre-detonation (engine knock or ping). The knock sensor (KS) is usually a two wire sensor. A 5 volt reference is supplied to the sensor and there is a signal return from the knock sensor to the PCM (powertrain control module). The sensor signal wire informs the PCM when a knock occurs and in what degree of severity. The PCM will retard the spark timing to avoid pre-detonation. Most PCMs have the ability to learn spark knock trends in the engine during normal operation. A P0328 code is a generic DTC, thus it applies to all makes of vehicles, and refers to a high output voltage of the knock sensor. In many cases, this means the voltage is above 4.5V but that specific value depends on the specific make and model of vehicle. This code refers to the sensor on bank #1. Symptoms Symptoms of a P0328 DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration Loss of power Irregular RPM Causes Potential causes of a P0328 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage Knock sensor has failed Loose knock sensor Electrical interference in circuit Low fuel pressure Incorrect fuel octane Mechanical engine problem Failed/faulty PCM Possible Solutions If you can hear engine knock (detonation), first fix the source of the mechanical problem and retest. Ensure the correct octane fuel was used (some engines require premium fuel, check the owners manual). Aside from that, for this code, most likely the problem will lie either with the knock sensor itself or the wiring & connectors going from the sensor to the PCM. Realisitcally, for the DIY vehicle owner, the best next steps are to measure the resistance between the two knock sensor wire terminals where they go into the PCM. Also, check the voltage of the same terminals. Compare those numbers to the manufacturer's specifications. Also, check all wiring and connectors leading from the knock sensor back to the PCM. In addition, you should also check the resistance using a Digital Volt Ohm Meter (DVOM) of the knock sensor itself, compare it to the vehicle manufacturers specification. If the knock sensor resistance value is out of spec, then it needs to be replaced. Other knock sensor DTCs include P0324, P0325, P0326, P0327, P0328, P0329, P0330, P0331, P0332, P0334 Register now to ask a question (free) Related P0328 DTC Discussions

Read more at: http://www.obd-codes.com/p0328
Copyright OBD-Codes.com

Aug 17, 2015 | Cars & Trucks

1 Answer

Does a 99 lincoln have a knock sensor?


On both cars the knock sensor is located in the intake valley.
a0028125.gif
the computer receive signals if engine knocking and adjust the timing till stop.Before replace the sensors make sure the engine have no other misfire ,bad gas or vacuum leak.plug scan tool and read the code.Only circuit problem will be a true knock problem. Inspect all wire connectors before start taking a part.

Mar 28, 2014 | Lincoln Cars & Trucks

2 Answers

P0325 what does it mean


P0325: Knock Sensor 1 Circuit Malfunction Bank 1 or 1 Sensor

- Knock sensor circuit short to ground
- Knock sensor circuit short to power
- Knock sensor circuit open
- Faulty knock sensor
- Faulty Engine Control Module (ECM)

Replacing the knock sensor usually takes care of the problem.

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Engine Control Module (ECM).

Feb 07, 2012 | 2005 Kia Rio

2 Answers

What causes a p 0327 diagnostic code on a 95 contour


P0327 - Knock Sensor 1 Circuit Low Input Bank 1 or Single Sensor
First check the knock sensor connector. If the connector is clean and secure, replacing the knock sensor usually takes care of the problem.

- An excessively low voltage from the sensor is sent to Powertrain Control Module (ECM) or Engine Control Module (ECM)

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power

Possible causes
- Knock sensor circuit short to GND.
- Knock sensor circuit short to PWR.
- Knock sensor circuit open.
- Damaged knock sensor.
- Faulty Powertrain Control Module (PCM) or Engine Control Module (ECM).


Test and check it. Hope helps.

May 12, 2011 | 1995 Ford Contour

1 Answer

I have a code p0325 knock sensor 1, circuit bank 1 or single sensor problem


A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. Knock sensors generally bolt into or thread into the engine block.

This P0325 code may show up intermittently or the Service Engine light may be lit constantly. Other knock sensor related DTC codes include P0330.

Symptoms: You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.

Causes: A code P0325 most likely means one or more of the following has happened:
* The knock sensor is faulty and needs to be replaced
* There is a wiring short/fault in the knock sensor circuit

Possible Solutions
* Check the resistance of the knock sensor (compare it to factory specs)
* Check for broken/frayed wires leading to the sensor
* Replace the knock sensor


Test it and tell us news.

Mar 15, 2011 | 1999 Nissan Maxima

1 Answer

Whit the oxigen sensors connected blown eng 1 fuse an engine shut off, only can run whit the sensors disconnected


there's a wire harness on the passenger side of the engine that controls the sensors. look for a shorted wire, maybe pink? follow the sensors back along the harness. good luck.

Jun 07, 2010 | 1998 Chevrolet Express

1 Answer

I have somes REV. problem. When I check whit the scanner throw me 2 codes: P1133 / P0325. Its a Outback S/W 2000 2.5l.Thanks for everything.


Off hand sounds like the wires. The first is the O2 sensor getting slow response. The other is your knock sensor. If the wires are in bad shape or coroded conection on the knock sensor this will confuse the computer and change timing and idle to correct it until it gets a good reading from knock sensor. This also slows the response to the exhaust system giving the sensor a slow or poor reading of exhaust gases. Hope this helps and have a good day.

Apr 17, 2009 | Subaru Outback Cars & Trucks

1 Answer

Knock sensor circuit problem


Well, you have another issue besides a knock sensor problem. A knock sensor code WILL NOT illuminate the check engine light. Check for other codes stored in the ECU. I have seen oxygen sensor issues cause knock sensor issues due to inaccurate fuel delivery resulting in engine ping at all times (causing the ECU to think that the knock sensor is bad because it's reporting ping at all times) - but also had codes for one or more O2 sensors.

Nissan Scope Technician- 10 years with Nissan

Oct 26, 2008 | 2000 Nissan Frontier

2 Answers

Knock sensor circuit


The code means there is a problem in the knock sensor circuit, that means the the knock sensor connector wire pins may have a problem, the wiring to the sensor may be damaged, or the PCM may have a problem, and of course the sensor itself, I have one question did you tighten the sensor to the proper inch pound setting of torque? if not this can cause a code to set because the sensor does not vibrate as designed to send a signal of a engine knock/ping.

Oct 16, 2008 | 2001 Chevrolet Venture

1 Answer

Sensor tyre for presure


When a Failure comes on in certain types of sensors it may just mean the sensor is at fault it may not mean Tyre pressure but check it anyway

Aug 11, 2008 | 2003 Saab 9-3

Not finding what you are looking for?
1991 Nissan 300ZX Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...