Question about Ford F-450

1 Answer

Would like to locate manual describing procedure for pulling headlamp switch from Ford 2000 450.

Posted by on

  • leopoldoburg Feb 17, 2009

    half the light dont work

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 51 Answers

Hi....there are spring clips that hold the dash bezel to dash. Carefully pop the bezel out (a small flat tip screwdriver would work well) and there should be 2 screws (or spring clips) that secure the switch to the bezel. Remove those, then the switch and reverse procedure for installation.

Chris

Posted on Aug 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove and replace headlights 2001 f350


is it a plastic lens AERO haedalmp or rectangular glass?

SECTION 417-01: Exterior Lighting 2001 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Lamp Assembly -Headlamp, Aerodynamic Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the headlamp assembly.
    1. Pull up and remove the two upper headlamp clips.
    1. Release the lower headlamp clip.
    1. Position the headlamp so the electrical connector can be accessed.
    1. Disconnect the headlamp electrical connector.
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

snorkelbobby_77.gif

Jul 24, 2011 | Ford F-350 Cars & Trucks

2 Answers

I cant seem to take out the headlight to change the turn signal after taking out the to bolts on top i cant seem to find or see a thrid or fourth bolt? o and my car is a 2008 ford focus se.


Please rate if this helps you.

Removal and Installation
  1. Remove the radiator grille. For additional information, refer to Section 501-08.
  1. NOTE: There is a blind metal snap located on the lower outboard side of the headlamp assembly that is disengaged by pulling upwards on the headlamp assembly.
    Remove the 3 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.
Headlamp Assembly adobe.gif Printable View (174 KB) n0077642.jpg
Item Part Number Description 1 W707594 Headlamp assembly bolts (3 required) 2 13008 Headlamp assembly 3 - Headlamp assembly electrical connectors (part of 14290)

Jan 19, 2011 | 2008 Ford Focus SE Sedan

1 Answer

Changing headlamp, how to..diagram


SECTION 417-01: Exterior Lighting 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Lamp Assembly-Headlamp (Explorer) Removal
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the parking lamp assembly. Refer to Lamp Assembly-Parking (Explorer) or Lamp Assembly-Parking (Mountaineer).
  1. Remove the headlamp assembly.
    1. Compress the self-locking tabs.
    1. Remove the headlamp assembly.
    1. Disconnect the electrical connector.
Installation
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n75014&c35=wsm%2clamp%20assembly%u2014headlamp%20%28explorer%29%2csxn%2c417-01%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_29.gif

Dec 29, 2010 | 1999 Ford Explorer

1 Answer

How to change light switch on 2001 mustang


Lamp Switch—Headlamp Removal
  1. Disconnect the battery ground cable.
  1. Remove the headlamp switch knob.
    1. Pull the headlamp switch knob out.
    1. Insert a thin tool into the slot, pull and remove the headlamp switch knob.
8c152ea.gif

Remove the instrument panel cluster finish panel.
  • Remove the screws and remove the finish panel.
2d039a1.gif

  • Remove the headlamp switch.
    1. Remove the screws.
    1. Remove the switch.
    1. Disconnect the electrical connectors.
  • 4cabe95.gif
  • Installation
    1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
      To install, reverse the removal procedure.

  • Hope this helps.. Cobra :-)

  • Jul 20, 2010 | 2001 Ford Mustang

    1 Answer

    Headlights removal ford explorer 96


    1. Check that headlamp switch (11654) is in the off position.
    2. Lift hood (16612).
    3. Release latch and swing filler panel to left or right.
    4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
    5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
    6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal. 7056091.gif
    Headlamp Assembly, Explorer
    Removal and Installation
    1. Disconnect battery negative cable.
    2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
    3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
    4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
    5. Remove attaching screws (4) located across top of grille.
    6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
    7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
    8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
    9. Disconnect wiring from headlamp bulb socket.
    10. If replacing headlamp housing, remove retaining collar and bulb.
    For installation, follow removal procedures in reverse order. Make sure to check headlamp aim. 568a220.gif

    Apr 02, 2010 | 1996 Ford Explorer

    1 Answer

    Need instructions to change out 2001 ford taurus headlight switch


    SECTION 417-01: Exterior Lighting 2001 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Headlamp Switch Removal and Installation
    1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
    1. CAUTION: Cover the end of the tool with tape to prevent damage.
      Insert a thin tool to remove the headlamp switch.

    1. Disconnect the electrical connectors.
    1. To install, reverse the removal procedure.

    Dec 24, 2009 | 2001 Ford Taurus

    2 Answers

    Need to replace head lamps on Ford Escape 2001,


    there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose them...here is a cpoy of the manual to change..good luck

    Headlamp Assembly Removal and Installation
    1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
      Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. NOTE: Pull headlamp assembly forward to access electrical connectors.
      Remove the headlamp assembly.
      1. Remove the three bolts.
      1. Loosen the nut.
      • Disconnect the electrical connectors.
      a0045726.gif
    1. To install, reverse the removal procedure.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

    Apr 22, 2009 | 2003 Ford Escape

    1 Answer

    2002 ford escape passanger side headlamp assembly removal?


    Removal and Installation
    1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
      Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. NOTE: Pull headlamp assembly forward to access electrical connectors.
      Remove the headlamp assembly.
      1. Remove the three bolts.
      1. Loosen the nut.
      • Disconnect the electrical connectors.
      a0045726.gif
    1. To install, reverse the removal procedure.
      • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

    Mar 03, 2009 | 2005 Ford Escape

    2 Answers

    Need to replace headlight assembly on 2005 Ford Escape


    ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

    n0037234.gif
    Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
    Removal and Installation
    NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
    1. Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. Remove the 3 headlamp assembly bolts.
      • To install, tighten to 5 Nm (44 lb-in).
    1. Remove the headlamp assembly nut and the headlamp assembly.
      • Disconnect the electrical connectors.
      • To install, tighten to 5 Nm (44 lb-in).
    1. To install, reverse the removal procedure.

    Jan 01, 2009 | 2005 Ford Escape

    1 Answer

    Headlight switch


    This is copied from a manual on CD I have, Hope it is of help.


    Instrument Cluster Finish Panel

    Removal and Installation
    1. Disconnect battery ground cable (14301).

    2. Remove headlamp knob from shaft by extending to headlamp ON position. Press clip in slot of knob shaft by inserting a small tool and pulling back; at the same time pull and remove knob.

    3. Remove two screws retaining instrument panel finish panel (044D70) above instrument cluster (10849).

    4. Pull instrument panel finish panel to unsnap one retaining clip above LH register.

    5. Pull instrument panel finish panel on both sides to unsnap two retaining clips.

    6. Pull instrument panel finish panel by sides of steering column to unsnap two retaining clips.

    7. Pull instrument panel finish panel to unsnap three retaining clips on RH side vertical/horizontal edge and remove instrument panel finish panel.

    8. To install, reverse Removal procedure.

    Sep 12, 2008 | 1995 Ford Mustang

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    91 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Ron Lankford

    Level 3 Expert

    5386 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...