Question about 2000 Toyota Tacoma PreRunner

1 Answer

Have 2000 toyota prerunner. have power to starter with key off. with key in on position no power at starter.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 880 Answers

Replace the entire switch, not just the tumblers. Before installing the new switch take it to a locksmith along with your old switch key and have the new lock keyed to work with your old key. This will save you from having a different key for the doors & switch.

Posted on Mar 16, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I lost my key to my Toyoto Tachoma how do i change the ignition cylinder without a key

You don't. There's a small pin holding the assembly in place that needs to be moved. Putting the key in the ACC position normally does that. I suppose you could take a big drill or chisel and just gouge the whole face out, but I'm not sure even that will expose the pin.

I think I'd take it to a dealer or a locksmith.

May 28, 2014 | 2000 Toyota Tacoma PreRunner

1 Answer

I own a 2000 toyota prerunner. My question regards changing a tire, both front and back. I can't tell where to place the jackstand. I see no "flat" areas ar "marked" areas to place...

In the front, place your jack stands on the stabilizer bar bracket that is bolted to the frame...
in the rear, put the jack stands on the rear end, closes to the outside as you can get...
Hope this helps ??

May 26, 2011 | 2000 Toyota Tacoma PreRunner

1 Answer

When i turn the key the starter does not turn over i checked the fuse inside the truck and the ignition fuse was working the power wires that are running to the starter are intact and tight idk where...

if its a standard the safety switch on the clutch auto or standard you need to check the starter to see if its getting power. If you have power at the starter then your starter is kaput. Good luck!

May 20, 2011 | 1999 Toyota Tacoma PreRunner

2 Answers

2000 tacoma wo't start. Turn key nothing. Will rool off and start. New barttery

Could be your starter. If you turn it and it doesn't crank, should be the starter.

Jan 14, 2011 | 2000 Toyota Tacoma PreRunner

1 Answer

I need to remove my 2000 Toyota Prerunner starter. How difficult will this be?

if its like the 4-runner or the tacoma its not very hard at all. its not too hard to get to so i think youll be ok i havent done one on this truck yet so im only guessing.

Mar 28, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

My 2000 toyota tacoma truck just won't turn on. My lights work, so I assume its not the battery or alternator..perhaps the spark plug or starter maybe the was running just fine yesterday..there...

So what does "turn on" mean?? either the engine turns over or it doesnt. If you hear 1 heavy click when you turn the key to crank, but it doesnt turn over, I would suspect you need starter contacts replaced, but only a starter/alt shop is going to repair it, most shops will only replace the starter. Sometime if yoiu just keep trying it will turn over. But dont let it go, get it fixed ASAP.

Mar 18, 2010 | 2000 Toyota Tacoma PreRunner

1 Answer

Location of fuel filter 2000 prerunner 2.7 engine

In the engine bay, on the firewall, behind the engine if it's a 2.7L I4. It'll be tricky to change due to space constraints.

Oct 29, 2009 | 2000 Toyota Tacoma PreRunner

1 Answer


assuming it is v/6 if my memory serves me correctly you have to remove the r/f wheel and remove it through the wheelwell. You will have to remove the transmission dipstick and tube held by a 12mm bolt on side of head (if A.T.M.) there are one or two bolts holding the brakeline to the frame, remove the bolts so you can move the lines out of the way, they are pretty flexible to move, just don't crush or kink. not gonna lie, the job is a bit of a pain, but is doable. good luck.

Dec 12, 2008 | 2000 Toyota Tacoma PreRunner

3 Answers

Clicking noise when starting 99 Toyota Tacoma lights work, dashboard lit Any thoughts?

solenoids are worn out, it will probably eventually start after 4 or 5 clicks but its annoying as hell

Jul 26, 2008 | 1999 Toyota Tacoma PreRunner

Not finding what you are looking for?
2000 Toyota Tacoma PreRunner Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides