Question about 1995 Ford Econoline

1 Answer

95' ford econline 350 van replacing waterpump and clutch fan how to replace.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

TO REPLACE WATER PUMP.REMOVE THE RADIATOR SHROUD HALVES.REMOVE FAN CLUTCH AND FAN.YOU NEED FAN CLUTCH WRENCH AND A FAN CLUTCH PULLEY HOLDER.YOU CAN RENT TOOLS AT AUTO ZONE OR BUY THEM AT A AUTO PARTS STORE.THE FAN CLUTCH BOLTS ARE LEFT HAND THREAD. REMOVE THEM BY TURNING CLOCKWISE.BEFORE INSTALLING NEW WATER PUMP COAT BOTH SIDES OF WATER PUMP GASKET WITH GASKET SEALER.TORQUE WATER PUMP BOLTS 18 FT LBS.

Posted on Mar 15, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 Ford Econline E350 that the front air comes out only out of the windshield area, no air out of face/feet area. Already replaced the Blending Door Actuator, please help! :)


Go directly towards a vacuum leak . The vacuum reservoir is notorious for going bad in the these vans , unfortunately you have to pull the heater box to repair it which takes numerous hours. Hopefully it is just a vacuum leak that's accessible. If its a diesel I would first check the vacuum pump , if its gas then start by checking the small vacuum line under the hood along the cowl on the right rear of the engine compartment. Pull apart one of the tee fittings and check for vacuum with the engine running . Then check inside the truck pass side under dash for a bunch of vacuum hoses . Got vacuum?

Mar 31, 2014 | Ford Cars & Trucks

1 Answer

Can I deactivate my speed control switch on a 1993 e-350 ford econline van by myself? and how


Remove the fuse---the 93's are the ones that Ford had recalls on because they were catching on fire. If your Van hasn't been in for the recall, you can still have it done---takes about 5 minutes to change the switch---Hope this helps.

Jul 06, 2011 | Ford E-350 Cars & Trucks

1 Answer

Van overheats in stop and go traffic


Can be one of the following
  1. Headgasget
  2. thermostat
  3. Waterpump
  4. Fan clutch
  5. timing

Jun 22, 2011 | Ford E-150 Cars & Trucks

2 Answers

1999 chevy tahoe 5.7L vortec 350 new thermostat,new radiator,new waterpump.still overheating?


REPLACE RADIATOR PRESSURE CAP AND CHECK THE COOLING FAN CLUTCH.WHEN YOUR ENGINE HOT WHEN YOU TRY TURNING CLUTCH FAN WITH YOUR HAND WHEN ENGINE IS HOT.THERE SHOULD BE RESISTANCE IN THE FAN.IF CLUTCH FAN SPINS FREELY WHILE ENGINE HOT.YOU NEED TO REMOVE COOLING FAN TO REPLACE CLUTCH.

Feb 23, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

How do i remove a fan clutch from a 2005 E-350 van. im down to trying to get the wrench on the nut, but i can't get it to move. thanks mike


Mike maybe you need to make more room to get in there, take the fan shroud off or other things to make room. Good luck.

Nov 18, 2010 | 2007 Ford E-350 Super Duty Length XLT

1 Answer

My 86 ford econline van died and won't start, replaced fuel pump, coil, plugs, ignition modular, fuel relay, fuel pump won't kick on


checkout the crank sensor give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your Van wish you the best of luck Michigan Man.

Mar 08, 2010 | 1986 Ford Econoline

1 Answer

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked...


You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Feb 22, 2010 | 1999 Ford Ranger SuperCab

1 Answer

REPLACE FUEL PUMP REGULATOR


What engine? It is attached to the fuel rail.

Mar 14, 2009 | 1997 Ford Econoline

2 Answers

Waterpump removing fan


Well, if it's a 5.0L engine, remove the 4 bolts holding the fan to the pulley. If it's a 4.0L engine, you need to hold the waterpump pulley still and break the nut loose holding the fan clutch to the waterpump. If you don't have a wrench that big, try using a long chisel on the edge of the nut and hitting it very hard with a hammer to break it loose.

Feb 15, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
1995 Ford Econoline Logo

737 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...