Question about 2002 Chrysler Concorde

1 Answer

How do you get the belt off when replacing the altenator?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers



Precaution when working on the electrical system always disconnect the NEG battery cable

1. Identify the idler pulleylocated on the dr side of the motor..... on the left side of the pulley is a bolt lossen it but dont remove

2. In the center of the puller is another bolt lossen and remove belt.

3. Reverse the steps
Good luck

Posted on Jun 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace alternator 2008 aveo


disconnect negative battery cable. Then remove rubber boot on altenator. Remove nut and cable attached. Unplug and remove wire harness also attached to altenator.
Loosen and remove both bolts holding on altenator.
Remove altenator.
Reverse process to reinstall. Pry on belt tensioner with pry bar and socket to loosen belt and place on altenator pulley after it is installed.
Last reattach battery cable and start vehicle.

Jun 04, 2012 | 2008 Chevrolet Aveo

1 Answer

2002 chevrolet pick up v6 excessive noise from belts replaced idler and tensioner ,no help power steering works fine ,altenator charging, a/c ok water pump ok rotated altenator, by hand when changing...


I would suspect the altenator, A/C pulley, or the belt. when you checked the altenator and a/c they have to turn smoothly with no play or roughness. If these checked out fine then I would check the belt, they do stretch.

Nov 28, 2010 | 2002 Chevrolet Silverado 1500

1 Answer

How to remove altenator from a 96 monte carlo 3.4 litre over head cam engine


  1. unhook battery
  2. take belt off - has a tensioner pull up on to release belt
  3. unhook wires from altenator-mark the wires so remember where they go
  4. take out bolt's that hold altenator on
  5. remove altenator -replace in reverse order

Nov 11, 2010 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

How to replace altenator?


  • remove the positive wire from the battery
  • disconnect the wires from the back of the altenator
  • remove the drive belt for the altenator, this may be a single belt that connects water pump and air conditioning compressor to the main crankshaft pulley or a seperate belt.
  • remove the alterator and replace with new unit
  • reinstall drive belt and wiring

Aug 10, 2010 | 1998 Pontiac Grand Prix

1 Answer

How to change altenator rib belt


there should be an idler pulley that also adjust the tension the tool usually used is a 3\8 or 1\2 ratchet

Jun 05, 2010 | 2000 Lexus ES 300

2 Answers

Replace altenator 2002 bmw 325ci


disconnect the negative battery. remove the belt by rotate the tensioner roller clockwise. from the left car side u will see three hexagon screw 13mm under the altenator. loose out the screw and remove the altenator. before that unplug the two wire behind the altenator.tq

Feb 28, 2010 | 2001 BMW 325

2 Answers

I have had a 1982 280zx since jan. of 2009 the


Are you over tightening the belt? If I remember correctly, you should have 1/4" belt deflection after you tighten it.

Check the factory service manual: http://www.xenons130.com/reference.html

Hope this helps!

Todd in Idaho

'69 510
'83 280ZXT
'91 300ZXTT

Nov 03, 2009 | 1983 Nissan 280ZX

3 Answers

93 dodge spirit engine noise


Have the belt run checked for proper alignment as it runs across the pulleys, this problem is almost always caused by belt alignment problems,

Dec 03, 2008 | 1993 Dodge Spirit

1 Answer

1994 geo metro


It's actually super easy.
All you need is your year and make alternator belt and a wrench.
Take off the existing altenator, take off the old belt.
Once the altenator is off you'll be able to look further down below where the altenator was. You'll see a metal wheel that's a little bigger than the one on the altenator. This is where the new belt needs to wrap around.
I found it alot easier to wrap the belts around the two wheels before putting the altenator back on the engine.
Make sure that all bolts and seals are sound. (that's the last thing you need falling off in the middle of nowhere!)
Hope it helped!

Aug 29, 2008 | 1994 Geo Metro

Not finding what you are looking for?
2002 Chrysler Concorde Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...