Question about 1996 Chevrolet Blazer

1 Answer

What is the correct part name for the front side of the rear end cover & gasket/seal?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,977 Answers

I assume that you are talking about the seal at the front of the differential were the drive shaft bolts to the flange,if so this is called the front differential pinion seal,if your talking about the differential cover at the back of the differential(most rearward part of the rear end) this is called the differential cover gasket.

Posted on Mar 15, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1987 Nissan se v-6 truck is leaking oil really bad is it the rear main seal


where is it leaking from
in front of the b ell housing--- sump gasket
out of the bell housing drain hole --could be rear main seal or gear box input shaft seal
from down the side of the motor in front of the bell housing--- rocker cover gaskets
is the sump over full

Sep 16, 2015 | Nissan Cars & Trucks

4 Answers

Oil leak on driveway coming from front of engine


Dear Sir,
Here is the oil leaking Problem Identifying Technique

Engine oil leaks from the valve cover gasket are common.

  • The intake manifold plenum gasket may leak and cause increased oil consumption/burning and a spark knock during acceleration; the gasket should be replaced.
  • External oil leaks from valve cover gaskets, intake gaskets (front or rear), and the rear crankshaft (rear main) seal area are common. The rear main seal is an unlikely source. Normally, the bearing cap mating surfaces (as well as the sealing surface between the oil pan and bearing cap) are the source for the leaks.
  • Engine oil leaks at the distributor can be misdiagnosed as leaks from theintake manifold seal, oil pan gasket, or rear crankshaft (rear main) seal. A revised distributor is available if oil is found inside the distributor.
  • If the oil filter casing shows signs of distortion from excessive oil pressure, theoil pump should be replaced.
  • Often misdiagnosed as a leaking oil filter gasket, the oil filter adapter can seep from between the adapter and engine block.
  • Carbon buildup on the top of the piston is common. As the buildup increases with mileage and over time, symptoms may vary from light ticking, to ticking/hammering, to hammering/knocking noises. Fuel injector cleaner often solves the problem.

  • I think it helps to analyse u r Problem

    Nov 02, 2012 | Toyota Cars & Trucks

    1 Answer

    1992 Ford Crown Victoria Oil Pan is leaking. Is this a major problem to replace? Fred


    It is recommended that you lift out the engine before attempting to replace the oil pan. Once the engine is lifted you can remove the bolts, remove the pan, clean all the old gasket material.
    Installation: Remove the rear main bearing cap oil seal Remove the timing cover oil seal Clean all the mating surfaces and seal grooves Install new oil pan front cover seals Install a new rear main bearing cap oil seal Install new oil pan side gaskets on the block Make sure the tabs of the front and rear seal fit properly as these are critical spots Attach the oil pan to the engine block and install the retaining bolts

    Feb 23, 2011 | 1992 Ford Crown Victoria

    2 Answers

    Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


    1. timing cover is leaking oil betwwen cover and block
    2. Disconnect the negative battery cable.
    3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
    4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
    5. Remove the accessory drive brackets attached to the timing cover.
    6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
    7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
    8. Remove the timing case cover front seal and gasket from the engine.
    9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
    10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
    11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

    To install:

    1. Install a new seal in the timing cover using a suitable seal installation tool.
    2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
    3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
    4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
    5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
    6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
    7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

    Do not hammer the damper into place as damage may result to the damper or engine.

    1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
    2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
    3. Install the accessory brackets.
    4. Install the fan and fan shroud.
    5. Install the drive belt(s) and adjust to the proper tension.
    6. Connect the negative battery cable.
    7. Start the engine and check for leaks
    8. .

    Jan 18, 2011 | 1992 Jeep Wrangler

    1 Answer

    Ford Explorer Sportrac 2001. some kind of oil leaking from the backend in the middle of the back tires.just wondering what it was and how to fix it


    If the leak is in the middle facing the back of truck most likely the rear end (differential) cover or gasket is leaking. If it is leaking in the front of the rear end it is most likely a rear pinion seal. Spray brake & parts cleaner to clean area. Let it dry & see if it is leaking in the front towards driveshaft or the rear towards rear bumper.

    Sep 06, 2010 | Ford Explorer Sport Trac Cars & Trucks

    1 Answer

    Rear axle removal on a 2004 f150 fx4


    First thing is to make sure you chock the front tires so the truck will not roll. Raise the rear end and set it on jack stands. Put the transmission in Neutral and make sure the parking brake is off. Remove the rear tires and disassemble the brakes on the side with the leaking seal. Place a drain pan under the rear differential and remove the cover. Remove the differential shaft lock bolt. You will need to turn the drive shaft by hand to access the bolt. It will be on the right side off the spider gear housing. Only use a 5/16 or 8mm 6 point box end wrench to remove the bolt. After you remove the bolt reach on the top of the spider gear housing and push the differential lock shaft down to remove it. Make sure the spider gears do not rotate after you remove the shaft. If they do you will need to realign everything to reinstall the lock shaft. Push the axle shaft in enough to remove the "C" clip from the tip of it. The axle will now slide out of the rear end. You can use the tip of the axle shaft to remove the axle seal. If you're changing the bearing as well you will need a slide hammer with axle bearing adapters to remove it. You can use a socket and hammer to install the new bearing and seal. Be careful not to damage the bearing and seal. I recommend packing grease in the back side of the seal. This helps prevent the spring on the seal lip from coming off. Assembly is the reverse. Clean off all the gear oil from the differential cover and the axle. You can use RTV as a gasket if the OEM gasket is damaged. Fill the rear end with new gear oil of the proper type. Refer to your owner's manual.

    Jun 05, 2010 | 2004 Ford F150

    1 Answer

    2004 Explorer: Rear differential cover is leaking, how do I fix i...


    put flat pan under the housing remove the bolts holding the cover usually 10 or 12 (1/2 or #12 metric) bolts? allow the rear end grease to drain... then scape off the old gasket clean with brake cleaner spray install either new gasket or form one with oil resistant silicone put the cover back on , dont refill the fliud for at least 12 hours if using silicone. Also check the front driveshaft rear end yoke seal....they sometimes leak making the illusion of a rear end pan cover leak...if that is leaking you remove the shaft carefully...remove the large yoke retaining nut, replace the press in seal...be sure retaining yoke nut is properly torqued when reinstalling .

    May 06, 2010 | 2004 Ford Explorer

    2 Answers

    Just bought 88 integra for $635 with 141k has ac, anyways it seems to have a small oil leak somewhere. Today I yanked the pvc and sprayed it out and blew through it easily. Any ideas besides the valve...


    at 141K there are many gaskets or seals that could be leaking.crankshaft seal,[behind main pulley],oil pan gasket or drain plug,timing cover gasket and so on.keep the oil changed regularly & full,get back to me @ 241K !

    Oct 11, 2009 | 1988 Acura Integra

    1 Answer

    Rear axle seal leaking on 1997 GMC Yukon 4x4


    You are Talking about the Main Cover on the Rear of the Rear end Correct???? If so, This is Just a Gasket and is Very easy to replace. The Gasket is Simply Worn out.

    Jan 17, 2009 | 1997 GMC Yukon

    Not finding what you are looking for?
    1996 Chevrolet Blazer Logo

    Related Topics:

    244 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8270 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...