Question about Dodge Neon

1 Answer

The groung wire that connects to the altenator, where does the other end connect, the motor or somewhere alse - if on motor, where this is for a 2000 dodge neon. this connection wire keeps breaking, mainly because it is so short now. if i was to replace it , where does it start. where would i find a diagram

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Your best solution is to ground it to the frame or the firewall. to use the wiring harness on your alternator, go to your local parts store and get a **** splice, crimper and correct size wire.

Posted on Mar 15, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lancer 4g18 misfires if the alternator is connected but if you disconnect it it runs smooth what can coz that


your altenator must have a fault or some of your wiring from altenator is burnt and so it's touching somewhere inside some other wires inside your car.let me know if you come alright.

Feb 15, 2013 | Cars & Trucks

1 Answer

Is it possible to connect headlights directly to battery


yes but its not recommended..in case a short somewhere is visible..do this for testing its much safer...connect a 10 amp battery charger to the backside of the headlight fixture wiring by the wires on the connector(a small jumper wire will help here..) groung goes to any metal surface or battery ground .. then the charger hot lead can be tested with the bare jumper end connected to the headlight wires one at a time.. if a short is present..the charger guage will peg over instantly.. this way, you wont burn up any wires.. good luck.. be carefull..

Jan 21, 2013 | 2000 Buick Century

1 Answer

2000 ford mustang electrical problems


You have a open connection somewhere,do you check the fuses especially the fuseable link at the positive battery post how about the power at the ignition switch it hot at all times,your disconnected somehow you might have to make a jumper wire to find what opened.

Mar 20, 2012 | 2000 Ford Mustang

1 Answer

I have a 2000 Dodge Neon. I drove it to a store and when I got back in the car it would not start. This has happened before and I was told it was the battery cable (broken wires). I had that fixed and...


This sounds like a bad starter but you should of got dash lights and headlights, if there are no headlights or park lights and no dash lights then theres a bad connection, start at the battery remove the terminals and clean posts then follow the groung wire to engine block and make sure theres a good connection to engine, a quick trick is to use jumper cables and connect one end to battery neg terminal and the other end to the engine, a good clean spot of metal and then see if theres power, if there is then its the ground cable to engine, if theres still no power then locate the box that the postive cable goes to, this pos cable goes to the starter and also to a fuse/relay box, check that connection. good day.

Jun 27, 2011 | 2000 Dodge Neon

1 Answer

My truck wont charge and the alternator is good,could it be a wiring problem like a fuseabile link


Hi check the earth wire at the battery and also the wires to the rear of the starter motor and altenator, make sure they have good contacts and are not touching each other. also make sure the main battery earth wire has a good contact to the body.

It sounds like the altenator is charging but the charge is not getting back to the battery. make sure the altenator belt is tight.

Im not 100% if this model has a fuseable link, bt your along the right lines something is not connecting somewhere.

I have found this fault is most commonly a melted wire but they can be difficult to find. Sorry I couldnt be more specific. It is difficult without seeing the car.

Regards

Dan

Jan 31, 2010 | 1991 Dodge Ramcharger

1 Answer

Engine dies in wet conditions


check all battery connections throughout the starter & altenator. Also the ground cables. One is loose somewhere

Jan 31, 2010 | 2000 Jeep Cherokee 2WD

1 Answer

Heating


check your fuses sometimes when a blower motor goes out or gets replaced it pops a fuse if this does not turn out to be the problem its probably the power connection to the blower motor itself make sure the ground wire got placed back on the motor and has a good connection to the body and the power wire is free of corrosion and has a good connection

if this doesn't work get a 12v tester light from your local Walmart Kmart Target there about 5.00 place the ground on the body and push the sharp end into the power wire for the blower motor make sure the a/c switch is on. the tester light should come on if it doesn't check connection to the body / ground and try again if the light comes on there is power and the motor may be bad or have a bad connection if it does not you must have a blown fuse or a problem with the power switch

I hope this helps

Jul 20, 2009 | 2000 BMW 3 Series

2 Answers

1996 BMW 328 IC Convertible Altenator ok but not charging battery


Sounds like the alternator may be missing an excitation current source.
Check the 'IGN' dash indicator lights when you turn ignition switch on prior to starting motor,
if not one of the below may be problem:-
1) check exiter control wire is connected to alternator D+ terminal (low current wire, +V with Ign on),
2) replace dash 'IGN' indicator lamp.

Jul 10, 2009 | BMW 328 Cars & Trucks

1 Answer

Altenator Not working Well


were talking about the big fat wire right? runs to the starter where the positive battery cable connects. Be sure the connections are clean and shiny bright on that cable and the battery connections and the starter connections. Make sure where the alternator bolts to the engine theres no corrosion and the bolts themselves are clean too, thats the ground for the alternator. Check the ground cable on the battery where it bolts to the body and or the engine too.

Jun 18, 2009 | 1995 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...