Question about 1993 Ford F250

1 Answer

Want to test Startup unit: Ford pickup 250 1993 /460 cubic measure/7.2 L

Ford Pickup 250 series 460C 7.2L 1993.
Three different times, I had to recharge the battery- a life time battery, and today,the engine will not startup even after my battery is recharged and holding the charge; therefore, I thought I could test the Starting unit with an ohm meter, but I do not know where the B+ circuit is located, and the other circiut.
Perhaps, I have more than one problem: Starting unit and the battery charger.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

Check the starter solenoid on the inner fender, should be on the drivers side fenderwell. Typically this is the problem. its a cheap part.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to know what I need to do to bypass the ac on a serpentine belt on a 1998 Ford Expedition. Is it a different belt that the regular one, or a different way to place it?


Well I will start by saying it can't be done.
Now, there might be a way if you can find a pickup truck without ac.
Standard pickup trucks with the 4.6 and 5.4 engines do come without ac in rare cases, especially ones sold in northern states. And the routing is the same for either truck engine without ac. But the belts are different between the pickup trucks and your Expedition. I don't know what difference is other than the Expedition belt is slightly shorter than the pickup truck belts with ac.
You may be able to run a shorter belt over the pulley above the crank and then over the pulley above the compressor, but I would expect to find bolts and brackets in the way.
And there is no way to know what the length would be without trying to measure the distance going that route, since engines without ac are routed differently. Some of the idler pulleys are in different places on the engines without ac.
And since all Expeditions come with ac, there is no belt listed without ac to get the length.

Feb 18, 2013 | 1998 Ford Expedition

1 Answer

How do you adjust valves on a 1991 toyota pickup


Hi Kassie, The HiLux comes with a number of different engines options. It may have an R series or Y series petrol engine or an L series diesel engine. The L series is adjusted with shims which have to be measured and replaced and the Y series has hydrolic lifters, needing no adjustment only replacement. The R series I cannot remember, but will find out and contact you a little later. Regards John

Nov 26, 2011 | 1991 Toyota Pickup

3 Answers

No sparks. Coil measures okay, makes sparks during bench test. Previous tech diagnosed bad ignitor & I replaced, still no sparks. Pickup coil ?


the rotor button may be bad..YOU CAN CHECL THE PICK UP COIL WITH A VOLT OHM METER or the dreaded bad timing chain, does the rotor turn with the motor. these are a real cheap durable unit.. EBAY CLICK HERE..HEI

Sep 01, 2011 | 1986 Chevrolet Nova

2 Answers

I need the firing order for a f150 1997 ford pickup 5.4


1997 Ford F 150 4WD Pickup 4.6 liter CNG SOHC V-8 VIN "9"

cf2d781.gif



1997 Ford F 150 4WD Pickup 4.2 liter V-6 VIN "2"

43c9217.gif




1997 Ford F 150 4WD Pickup 5.4 liter SOHC V-8 VIN "L"

3b920f0.gif


Hope this help (remember rated and comment this).

Mar 21, 2010 | 1997 Ford F150 Regular Cab

1 Answer

What is the firing order of a Ford Pickup, model


5.0

Firing Order 1-5-4-2-6-3-7-8

5.8

FIRING ORDER: 1-3-7-2-6-5-4-8



Mar 07, 2010 | 1986 Ford F150 SuperCab

2 Answers

Needa serpentine belt routing diagram for a 1990 F150 pickup truck


1990 Ford F Series Pickup 6-Cyl. 4.9 L
Automotive V-Ribbed Belt (Standard)
Serpentine; W/A.C.; W/Auto. Trans

bbb6423.jpg

Automotive V-Ribbed Belt (Standard)
Serpentine; W/A.C.; W/Man. Trans
7b961e6.jpg


Automotive V-Ribbed Belt (Standard)
Serpentine; W/O A.C
5ad2e3d.jpg


Is this engine is your model, I hope help you with this. Good luck.

Sep 11, 2009 | 1990 Ford F150

1 Answer

Suspension bushings compatibility


According to the three sites I checked all of the Hilux models from 1979-1997 have interchangeable bushings.

May 28, 2009 | 1987 Toyota Pickup

Not finding what you are looking for?
1993 Ford F250 Logo

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...