Question about 1996 Cadillac Seville CA Value

1 Answer

Have ab 96 cadillac seville we replaced the selonoids and it still wont shift. i wasb told tooo have my computer flashed

Posted by on

  • Ned  White
    Ned White Mar 15, 2011

    I did the same thing to my car, same tranny, thm 4l30e, The solenoids didn't do anything but get rid of the check tranny light, I changed out the computer, didn't change a thing. I have never heard the flash thing before, what is it?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 829 Answers

Is it struck in third gear or does it stay in low?If it is stuck in third that means that it is limp mode and has a hard diagnostic code stored in the computer .Probaly a bad sensor .If starts out in low gear and never makes the 1-2 shift it could be that the 2nd clutches are not holding or that the computer is not getting a vehicle speed sensor signal and does not know the vehicle is moving.It waould pay to have a diagnostic run and not just throw parts at it.I am sure there is some sort of code stored and if I knew what it is I could most likely tell you what is wrong.There is no way to guess.Let me know if i can help.

Posted on Mar 15, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does my ABS light stays on and sometimes i get a vibration in the brake petal causing my 2002 Cadillac escalade not wanting to stop?


Sounds like a fault with the Antilock Braking System. The vibration in the pedal is the ABS working. With your foot on the brake pedal, it releases and re-applies the brakes to stop a skid from the wheels locking up. You need professional service for brakes.

Seems to be a known issue on all Cadillac and requires the ABS module to be replaced.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille Cadillac DeVille ABS Light Due to ABS Control Module Failure. This is a verified problem based on 126 reports. Learn more about this problem, when it occurs ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville STS Traction control and ABS lights stay on dash. This is due to ecbtm Module gone bad. replace Module and this should fix the problem. You can go by the VIN and ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille DTS ABS Light Due to Control Module Failure on Cadillac DeVille DTS. The anti-lock ... ABS and Traction control light stays on. ... abs light to abs control stay on.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville SLS ABS Light Due to Control Module Failure on Cadillac Seville SLS. The anti-lock brake ... SLS135,000Jumsee. Abs and traction lights stay on when started.

Jan 12, 2016 | Cadillac Cars & Trucks

1 Answer

1994 cadillac sts will shift all gears except park. ignition only turns off part way and key wont come out. So i put in neutral and push ABS pedal down before turning car off


if its column shift, check the linkage under the hood make sure bolt or pins are tight and not slipped out of the joint. if not topside linkage, most likely is the transmission shift plate that connects to the transmission shift shaft, usually a single bolt just needs tightening. usually a 10 mm or a 13 mm socket/wrench((IF its a floor shift then the cable is out of adjustment or stretched, would need to be replaced if adjustment plate is not loose))

Sep 08, 2012 | 1994 Cadillac Seville

1 Answer

Abs relay location


There is no "ABS Relay" in a 2003 Cadillac Seville. The ABS pump motor is switched on and off by the ABS Control Module.

Jan 09, 2012 | 2003 Cadillac Seville

1 Answer

94 sls shifting problem . replaced: solinoids , cluster, computer, transfluid,and filter. stayes in 2nd gear and drived 45 at 4000rpms and gived me 117 codes and 76 codes witch are shorted shift solenoids


i have a 1994 cadillac seville sls and it wont shift out of 2nd gear i have replaced the shift silenoid "B" and the vss and it still wont shift and the pcm is still good. What else could it be?

Mar 21, 2010 | 1994 Cadillac Seville

1 Answer

1996 Cadillac SLS ABS and Traction lights


check the abs connections at every wheel .

Jan 04, 2010 | 1996 Cadillac Seville CA Value

4 Answers

Where is the shift selinod located at. how hard


remove the transmission pan they are bolted to the valve body inside the pan.

Mar 16, 2009 | 1995 Cadillac Seville

1 Answer

1993 cadillac seville


It might be the fan relay switch. When the car gets warm check to see if the fan comes on.

Sep 13, 2008 | 1990 Cadillac SeVille

Not finding what you are looking for?
1996 Cadillac Seville CA Value Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...