Question about 2006 Chevrolet Trailblazer
For the drivers side, reach down by your alternator and over behind the headlight. You'll feel a 3" round rubber boot. Slip this off and now you can remove the light bulb.
Passengers- Remove the top of the air cleaner, at that point you'll have complete access to the rubber boot and bulb.
Posted on Mar 18, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
My niece has a jimmy, they should be the same. The inside should be the high beam, the outside the low, DO NOT TOUCH THE GLASS ON NEW BULBS! Oil will cook on them and pop them! Both come off the same way. Take off the big rubber thing. They are soft but over hard plastic. Just pull them off. If you have trouble, you can flip the little wire clips that hold the headlight housing in place, this will give you room to see the rubber caps enough to figure them out better. The bulb assembly rotates CCW counter clockwise, and should slip out easily. Take the wires and plug off. it should be obvious how it pulls off. Snap the new bulb into the wires without touching the glass part. Gently replace in backwards order as you removed it. Put the rubber caps on, they keep water off the bulbs. It will break them!
The passenger side was harder for me. I had to take the air cleaner off, the whole cover and filter.You should be able to see or feel the same type caps, The low beam outside, High beam inside. The same 2 wire clips are there to release the housing. Everything pretty much goes the same, other than the air cleaner has to be removed and replaced. And make sure the rubber cap is replaced! Good Luck and good motoring!
Posted on Dec 19, 2008
when the hood is open there are two pins that have to be pulled. they have a 90 degree bent end that have to be rotated and pulled directly up. once both are pulled the headlight can be slid out and headlight changed.
Posted on Jan 05, 2009
There are not two rods, there are two clips one under fender weild and one right above the light on top of the cover. Pull up on these two clips and pull the light forward a couple of inches and remove the dust cover. You have to take the air filter cover off to be able to reach in and replace the light. It took me about 10 min to figure these out but hope it helps out.
Posted on Jan 14, 2009
Simple! (I have the same model as well) Pop off the front chevy grill - it's held on with spring clips. Then look at the headlight assembly - there are 2 slide clips on either side, near the top - they have a tab that is bent forward - lift them UP. It may take a little force as they are usually stiff. The headlight assembly can then be pulled off the car, and the bulbs replaced.
Posted on Apr 18, 2009
if both lamps dont work a common problem was the headlamp module. It looks like a black relay in the underhood fuse block (next to the master cylinder), there is two black small relays right next to each other (they used to say 15016745 on top in white letters.) One is for the low beams and one is for the fan clutch. Swap them and check the lamps - if the come on, go get a new one at the dealer and replace the bad one. If you leave the bad one in the fan clutch your gas mileage will be bad and your ses light will come on.
Posted on Jul 24, 2009
Tips for a great answer:
Jul 06, 2017 | Cars & Trucks
Aug 31, 2013 | 2006 Chevrolet Trailblazer
Jan 13, 2013 | 2006 Chevrolet Trailblazer
Oct 26, 2011 | 2004 Chevrolet TrailBlazer
Jul 15, 2011 | 2006 Chevrolet Trailblazer
Dec 05, 2010 | 2006 Chevrolet Trailblazer
Nov 26, 2010 | 2006 Chevrolet Trailblazer Ext
Dec 01, 2009 | 2006 Chevrolet Trailblazer Ext
Sep 24, 2009 | 2006 Chevrolet Trailblazer Ext
221 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: