Question about 1992 Lincoln Town Car

1 Answer

What is the cost for a egr valve pipe connector.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

I just bought one from the dealer for $101.00 with tax.

Posted on May 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 toyota avalon EGR VAlve troubleshooting


onestly, your best bet is to replace the valve if nor mistaking it comes with the sensor, make sure pasages are not blocked, start the car with out the egr it will go up and down rpm and will be noisy if egr pipe is not blocked

May 05, 2012 | Toyota Avalon Cars & Trucks

1 Answer

How to replace head gasket on 4 cylander


2.6L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Hood
    • Accessory drive belts
    • Accelerator cable
    • Positive Crankcase Ventilation (PCV) valve and hose
    • Air intake duct
    • Fuel pressure regulator vacuum line
    • Canister hose
    • Brake booster vacuum line
    • Engine wiring harness connectors at right wheel housing
    • Ground cable connector at the intake manifold, starter and firewall
    • Heated Oxygen (HO2S) sensor connector
    • Alternator wiring connectors
    • Oil pressure switch connector
    • Starter motor harness connectors
    • Ignition coil connector
    • Spark plug wires
    • Distributor
    • Exhaust front pipe
    • Exhaust Gas Recirculation (EGR) gas temperature sensor connector
    • Air pump
    • EGR pipe
    • Heat shield
    • Exhaust manifold
    • Throttle Position (TP) switch connector
    • Cooling fan
    • Water pump pulley
    • Power steering pump
    • Intake manifold
    • Crankshaft pulley
    • Front cover
    • Timing belt. Refer to the Timing Belt unit repair section.
    • Valve cover
    • Rocker arms
    • Camshaft
    • Cylinder head
Cylinder head bolt loosening sequence - 2.6L engine

tecnovative_96.gif
  1. To install:
  2. NOTE: Refer to Section 1 of this manual for the cylinder head torque sequence illustration. The illustration is located after the Torque Specification Chart.
  3. NOTE: Lubricate the cylinder head bolts with clean engine oil for assembly.
  4. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows:
  5. Step 1: 58 ft. lbs. (75 Nm)
  6. Step 2: 72 ft. lbs. (98 Nm)
    1. Install or connect the following:
    2. Camshaft
    • Rocker arms
    • Valve cover
    • Timing belt
    • Front cover
    • Crankshaft pulley. Tighten the bolt to 87 ft. lbs. (128 Nm).
    • Intake manifold
    • Power steering pump
    • Water pump pulley
    • Cooling fan
    • TP switch connector
    • Exhaust manifold
    • Heat shield
    • EGR pipe
    • Air pump
    • EGR gas temperature sensor connector
    • Exhaust front pipe
    • Distributor
    • Spark plug wires
    • Ignition coil connector
    • Starter motor harness connectors
    • Oil pressure switch connector
    • Alternator wiring connectors
    • HO2S sensor connector
    • Ground cable connector at the intake manifold, starter and firewall
    • Engine wiring harness connectors at right wheel housing
    • Brake booster vacuum line
    • Canister hose
    • Fuel pressure regulator vacuum line
    • Air intake duct
    • PCV valve and hose
    • Accelerator cable
    • Accessory drive belts
    • Hood
    • Negative battery cable
    1. Fill the cooling system.
    2. Start the engine and check for leaks.

    tecnovative_65.jpg

    Feb 05, 2011 | 1997 Isuzu Rodeo

    1 Answer

    Random missfire all cylinders 1996 honda civic sohc


    Check the EGR valve system. Honda's are prone to the exhaust supply to the EGR valve getting clogged with carbon at the valve port entrance. A clogged EGR valve can cause the engine combustion temperature to climb and then for pre-ignition miss-fire events to become common. The EGR is located inside the elbow of the air filter pipe at the back of the engine on the left beneath the coil. Anything you can temporarily remove to provide access the better. The EGR valve has two bolts, an electrical connector and a vacuum line attached to its top. Take it off and give it a really good clean, carburettor or brake cleaner works well in conjunction with cloths and brushes. Once cleaned like new replace everything including the vacuum line and electrical connector.

    May 09, 2010 | 1998 Honda Civic

    1 Answer

    Where is the egr valve on a 2005 dodge 1500 5.7L


    The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.

    2efe0f8.gif

    Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

    Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
    The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

    TY for using Fixya; remember rated this post.

    Apr 14, 2010 | 2005 Dodge Ram 1500

    1 Answer

    How do I locate and replace EGR valve?


    Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT

    REMOVAL PROCEDURE
    1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
    1.
    Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
    2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.

    Jan 30, 2010 | 2001 Buick Regal

    3 Answers

    Obd II says egr valve problem. new egr valve stil have dash board light sheck engine


    normally - 4 cycles (heat up and cool down) are required to let the ECM callibrate to the new valve.

    Please do this, then have the computer re-set.

    Thanks

    Jul 06, 2009 | 2001 Mercury Grand Marquis

    1 Answer

    How do I replace an egr valve on my 2000 Nissan Maxima? Where is it in relation to the air intake and the throttle body?


    When you pop open the hood, look at the side of the engine on your right (driver's side). Underneath all the air intake duct that connects to your air filter is the EGR valve. It may  have a grey plastic top with an electrical connector attached to it (this top is about an inch and a half to two inches in diameter), a middle section below this that is made from a silvery metal with two rubber hoses plugged into it, and below this a bottom section with a metal pipe maybe three quarters of an inch in diameter connected to it. The metal pipe curves around and goes back behind the engine. There are two bolts that the valve is mounted on. To remove the valve, first you have to get a bunch of hoses and stuff out of the way to expose it, then disconnect the hoses and electrical connector from the valve, then disconnect the metal pipe connected to the base, then remove the two nuts on the two bolts. There is a gasket between the EGR valve and the engine which you will have to replace. It cost less than two dollars, good luck and hope this helps. WHen installing just do everything on revers. If you not sure if you can recall how the hoses goes back, take picture with your cell phone as reference. 

    Jul 05, 2009 | 1999 Nissan Maxima

    1 Answer

    Location of EGR Valve


    Found the info!!

    This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
    On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!

    Mar 14, 2009 | 2005 Dodge Dakota

    2 Answers

    I HAVE A 2005 3.3 DODGE CARAVAN HAS PO405 AND PO404. I PURCHSED NEW EGR VALVE IT ERASED CODES I DROVE SHORT DISTANCE AND THE 405 CAME BACK ON WHAT HAPPENED


    egr valve replaced and check engine light comes back on with p0405-check wiring at connector-if ok try performing at battery static discharge-disconnect both battery cable ends-and touch cables together-this discharges all ecu capacitors and resets adaptive memory

    Jan 22, 2009 | 2005 Dodge Caravan

    1 Answer

    EGR VALVE


    REMOVAL PROCEDURE
    1. Turn OFF the ignition.
    2. Disconnect the EGR valve electrical connector.
    3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back.
    4. Remove the EGR valve retaining bolts.
    5. Remove EGR valve assembly.
    6. Remove the gasket.
    INSTALLATION PROCEDURE
    1. Install the EGR valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
    2. Reinstall the bolts through the EGR valve into the intake manifold. Tighten Tighten the EGR bolts to 30 N.m (22 lb ft).
    3. Connect the exhaust pipe assembly to the EGR valve.
    4. Reinstall the exhaust pipe bolt. Tighten Tighten the nuts to 30 N.m (22 lb ft).
    5. Connect the EGR valve electrical connector

    May 28, 2008 | 2000 Chevrolet Impala

    Not finding what you are looking for?
    1992 Lincoln Town Car Logo

    Related Topics:

    29 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lincoln Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a Lincoln Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...