Question about Chevrolet Colorado

Open Question

G force performance chip hook up wanted to know which wires to splice into.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: installing chip and want to double check wiring. Need to find IAT/MAF sensor diagram for 2003 Ford Ranger

Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.

Posted on May 29, 2009

  • 4793 Answers

SOURCE: I have bought an upgrade

dave,you need to talk to the chip suppliers,cos if anyone gives you the wrong answer,your f....d.(how many chip suppliers are there??)
we have "superchips" in the U.K.

Posted on Sep 22, 2010

emissionwiz
  • 75817 Answers

SOURCE: I want to install performance chip on 2010

Connect the wires to on what? Please explain what it is you have and what you want to connect it to. Until I have this information I can't answer on way or the other.

Posted on May 10, 2011

bonedivers
  • 1140 Answers

SOURCE: im wanting to hook up

will need more info on vehicle

Posted on Jun 14, 2011

  • 5370 Answers

SOURCE: I have a 2002 Dodge Dakota V8 how do I install a G

The iat ground wire is dark green/dark blue and iat signal wire is red/brown wire. --------- Click this link for more help:--- http://technoanswers.blogspot.com/2011/06/2002-dodge-dakota-v8-iat-sensor-wire.html ---------- This should help.Thanks.Helpmech.

Posted on Jun 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a G Force performance chip, I need to know what wires to splice into I think its 1& #5 wires is this correct? and is this going to help my power and MPG?


You didn't include your car info to know the wiring, regardless, what you need to do is return it within their allowed time to get your money back. If you open one up you'll likely see a computer chip looking thing and a few other small parts on a board, impressive. Upon closer examination you'll find the chip is connected to nothing and the actual circuit is only running through several resistors on the board. All this thing does is change the resistance reading going to the computer to fool it into running rich then the O2 sensors have to force the computer to regain balance. It can not increase your mileage. It might add a little power under heavy throttle when the O2 circuit is ignored by the computer, it might also throw things off enough to cause many problems. You could simply go to radio shack and buy a resistor for a few cents and have the exact same results.

Jun 15, 2015 | Cars & Trucks

1 Answer

What wires do I use on my 2012 chevy truck.to hook up my gforce performance chip


G-force has what wires to hook to on the air inlet temp sensor, didn't help much on my Chevy truck. Seems to have a little more power but mileage didn't improve much.

Oct 25, 2013 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Hookup of G Force Performance Chip to a 6 wire IAT sensor for 2003 Hummer H2?


You have to contact the mfg of that product

It won't do a thing for your vehicle

Waste of money & may do some harm

Send it back

If you have no instructions that should send up
a red flag & G Force never has them apparently

Nov 25, 2012 | Cars & Trucks

1 Answer

I have bought an upgrade performance chip for my 2008 yaris, and have learnred that the chip splices into the IAT sensor wires which are part of the MAF sensor. I see five wires on the MAF sensor, but...


dave,you need to talk to the chip suppliers,cos if anyone gives you the wrong answer,your f....d.(how many chip suppliers are there??)
we have "superchips" in the U.K.

Sep 22, 2010 | 2008 Toyota Yaris Sedan

1 Answer

Computer chip instalation


I am guessing you purchased this item off of eBay. Son, this so called "chip" is not ment for your car.

I am a 5 year owner of my 91 300zx Twin Turbo'ed. My z was once a NA and I swapped it over.

If you want a performance chip I suggest you check out. concepetzperformance.com Z1motorsports.com and 300zxclub.com

May 11, 2009 | 1994 Nissan 300ZX

1 Answer

Locating the iat sensor on a chevy tahoe 2008


Yes. That is exactly it. The Air Intake Temp Sensor is built into the Mass Air Flow Sensor on the Air Filter Box. Below is a picture...
29f8daa.jpg
6d7178d.jpg
I personally have not connected one of these Chips to a Tahoe...What I can provide you with, is the Connector Diagram so you know exactly what Wires you need to Splice in to. See below...
ce630fe.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesisitate to ask...Thanks again, JShreader.

Mar 31, 2009 | 2008 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...