Question about 1995 Ford Bronco

1 Answer

How to find video sites for a 1995 ford bronco wheel bearings rotors ball joints

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Try www.1aauto.com

You can also find alot of there video's online at youtube.com

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Contact between brake caliper and disc brake on Ford f350 possible ujoint problem or ball joints some up and down movement in hub when wheel is removed


Since you mentioned U-joint, I'll assume you're talking about a 4x4 F350 front wheel. I am not that familiar with the F350 4x4, but if the rotor is touching the brake components (and you have good pads), the problem is not the ball joints or the u-joint. It is most likely the wheel bearings.
And if it's touching the caliper or anchor bracket, the bearings are pretty bad.
Jack the wheel off the ground. Grab the top and bottom of the tire, and see if there is any "play" in and out to the truck. There should be virtually no play. If not convinced, check the other side for comparison.

Apr 12, 2015 | Ford F-350 Cars & Trucks

1 Answer

Replace wheel bearing front awd 2010 ford edge


remove caliper, rotor, caliper bracket, lower ball joint shaft and two strut bolts. remove bearing housing and any snap rings. remove old bearing. replace and repeat in reverse. watch the abs sensor! costly if damaged. This is not for beginners...

Sep 19, 2014 | 2010 Ford Edge

1 Answer

We have a 2004 Ford Expedition when you turn right there is a noise coming from the wheel on the driver side. At first it was like a grinding noise so we changed the inner/outer tie rods. The noise...


There are several components that could cause noise from the front when turning. The components to be concerned about are, Wheel bearings, Ball Joints, Tie rod Ends, CV joints and brake rotors.

Wheel Barrings:

Jack the car up under the control arm until the wheel is off the ground about 3 inches. Slide a pry bar under the tire and place the other hand on the top of the tire. As you lift and lower the pry bar fell for loose movement in the tire. If there is such movement you have a bad wheel bearing.

On your vehicle this is a sealed Hub.

Ball Joint:

Repeat the test above and watch the upper and lower ball joints for movement. Is there is movement replace the bad ball joint.

Tie Rod ends:

You have changed the inner and outer tie rod ends so you are probably covered there.

CV joint:

The Joint is housed in a rubber boot. If you can feel the joint inside the boot you can turn the tire forward and back and feel for play in the joint. If you are not able to feel the play you can loosen the clamp on the boot and push the boot out of the way. Then repeat the test.

Brake Rotors.

You have already changed the rotors so this is not likely the issue.

Apr 06, 2011 | 2004 Ford Expedition

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Do you have to take the ball joints off to change the universal joint in the front axle on a 2002 ford f350


no you do not just remove brakes wheel rotor and wheel bearring hub . Then pry shaft out straight it my be a little hard but it will come out.

Oct 30, 2010 | 1994 Ford F150 Styleside Supercab

1 Answer

How do you remove the rotors on a 1995 ford bronco


The rotors on most vehicles are removed by (1) removing the wheel, (2) remove the silver colored cap in the center of the hub, (3) remove the cotter pin that goes through the axle nut and axle, (4) remove the axle nut, (5) remove the disc brake caliper (6) now pull on the rotor. It should slide off the axle. Reassemble in reverse order, being sure that the axle bearings are in place with proper amount of grease.

Oct 25, 2009 | 1995 Ford Bronco

2 Answers

Change the front wheel bearings on a 2005 taurus


Remove wheel
Remove axle nut
Remove outer tie rod nut
Leave outer tie rod nut on 3-4 threads
Hit spindle area where tie rod is mounted very hard with a large hammer (wear Saftey glasses)
The tie rod should loosen up and you remove it off spindle.
Remove lower ball joint nut
Leave nut on 3-4 threads
Hit spindle area where ball joint mounts (wear saftey glasses)
Carfully pry down the lower control arm too remove ball joint from arm.
Press in the axle towards the trans. out of the wheel bearing.
Place a piece of wood between the shock and inner fender to give yourself room to work.
Remove the three 15mm bolts that hold the wheel bearing on.
Hit wheel bearing out with hammer (wearing saftey glasses)
You may need to break a sweat on this part. Somtimes they are rusted in.
Be carfull not to damage the ABS sensor.

Reverse procedures to install

Sep 08, 2009 | 2005 Ford Taurus

2 Answers

Wheels bearing stuck rotors wont come off. Howdo Iget them off?


I hope you ready for some fun. I just did mine on the same car. first off DO NOT listen to the idiots on the internet. They are stuck for a reason. you can't just pull them off. unless you can bench press 4000 lbs. that is!!! you need to remove upper ball joints lower ball joints then steering arm. the whole hub assembly will then come off. this is assuming you already took the 36mm axle nut off. next remove the 4 bolts on the rear wheel bearing assembly. and take in to machine shop they will have to press out bearings so that you can replace your rotors. as long as your doing that you might as well have them put in new bearings at the same time. this is not a job you want to do again anytime soon. also I replaced the lower ball joints because my were somewhat bad. I am saving you a big headache here. they charged me 20 bucks per side for pressing bearings in and out and 20 more for pressing new ball joints in and out. new bearings cost me 40 per side. so all in all it cost me 300 bucks for everything. but at a shop ( I've already checked) this is a $750 job. Have fun!!!! At least you know you'll be saving money. by the way. the front axle nut is a 36mm torqued to 180ft.lbs. for your info. also wheel torque is 81 ft lbs.









Jul 09, 2009 | 1995 Honda Accord

1 Answer

Replace ball joints


Remove wheel, before removing the ball joint, mark with a with pencil or some identifing object the exact location remove the ball joints and replace exactly the same way you removed them. Eliminates the need for a alignment. The ball joints located in the wheel well, you will need a good hammer about 3 to 4 lb, they have to be kocked out.

Jun 28, 2009 | 1986 Ford Bronco II

1 Answer

How do we remove wheel bearing on 1995 Mitsubishi Galant ''S''


According to the chilton manual you have to: remove the speed sensor,caliper and brake pads,brake rotor from hub assembly, disconnect the upper ball joint from steering knuckle & pull the knuckle outward. From the back of the knuckle remove the four bolts and then remove the hub and bearing assembly from the knuckle

Mar 14, 2009 | 1995 Mitsubishi Galant

Not finding what you are looking for?
1995 Ford Bronco Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...