Question about 2001 Toyota Tacoma

1 Answer

Where is the mass airflow sensor located on a 2001 toyota tacoma

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

THE MASS AIR FLOW SENSOR IS MOUNTED TO THE INTAKE AIR HOSE OF THE AIR CLEANER ASSEMBLY. O2 SENSORS LOCATION.YOU HAVE 2 # O2 SENSORS.YOU HAVE ONE THE EXHAUST MANIFOLD.THE OTHER SENSOR LOCATED DOWN AT THE CATALYTIC CONVERTER. YOU SHOULD ALSO REPLACE THE O2 SENSORS TO HAVE THE BEST READINGS FOR AIR MIX.

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is iat sensor located on 2006 tpyota tacoma 4,ol ?


Intake Air Temperature (IAT) sensor and Manifold Absolute Pressure (MAP) sensor are combined into a single assembly which is called Mass Air Flow (MAF) sensor. This MAF sensor is located on the air filter box near air filter hose, and is connected with a five wire connector. You cannot replace the IAT sensor alone. Instead a MAF sensor is replaced altogether.

25646166-ts5vql1j3jwqenesgxdwpnsg-5-0.png



25646166-ts5vql1j3jwqenesgxdwpnsg-5-2.png
Thank you for visiting Fixya.

Apr 14, 2015 | 2006 Toyota Tacoma

1 Answer

Where is iat sensor on 2006 toyota tacoma 4.ol 4door located ?


This is the 2001-2012 Toyota Tacoma wiring diagram, Toyota Tacoma IAT (Intake Air Temperature) Sensor Location and the Toyota Tacoma MAF (Mass Air Flow) Sensor Location, also included is a pinout of the sensor. You are likely installing a performance chip or a cold air intake kit for increased HP (Horsepower). You will want to be sure to disconnect the car battery before adding performance products.




Here is the Toyota Tacoma's Iat sensor diagram:




ab0b7213-0c7f-459c-b26e-77a685236e74.jpg

Apr 14, 2015 | 2006 Toyota Tacoma

1 Answer

Where is the mass airflow sensor on a 2001 dodge intrepid


The mass airflow sensor is located in the air intake manifold. It usually has several wires attached to it.

Aug 21, 2012 | Cars & Trucks

1 Answer

2002 toyota tacoma with a p1135 code and a # 4 cylinder misfire


I have had a problem like that on my Isuzu Rodeo Turns out the o2 sensor was bad. The computer reads it as not enough fuel. The mass airflow sensor will dump more fuel causing the engine miss fire.
You might check the codes again and see if you get the code for the 02 sensor. If so you can try to unplug the 02 sensor, the ck engine light will remain on, however the car should run without any issues.
Good Luck!!

Feb 21, 2011 | Toyota Tacoma Cars & Trucks

3 Answers

Replaced mass airflow sensor in 2001 tacoma twice. Is their a way to clean, bypass, etc. new unit lasts about two months, ie engine light comes back on and mechanic is ready to replace sensor, clean...


If the new unit only lasted a couple of months, and the engine light goes back on, I think that you should try to have it replaced at the auto parts store under their 90 day warranty policy, if they have that.

Try to go to a reputable source such as Autozone or Advance Auto Parts where they have a more liberal return and refund policy.

Usually, a MAF sensor once replaced shouldn't go bad in such a short time span.

Maybe, check that the voltage to the MAF sensor is not too much for the sensor, causing it to go bad. If that's the case, the computer reference signal voltage may be the culprit.

Good luck on this repair.

Dec 19, 2010 | 2001 Toyota Tacoma

1 Answer

2001 Tacoma running rich but the scanner is reading a lean code


No, disconnecting the sensor and seeing no change would be a indication the maf was bad. Your computer takes information from your mass air flow sensor (maf), o2 sensor, cam position, and knock sensor to regulate the correct mixture. I would suspect a bad o2 sensor upstream. Try taking off the o2 sensor and seeing if there is black carbon on the base of the o2 sensor. If it has black carbon on the base it could be a bad o2 sensor. This problem could also be easily solved by hooking up a mechanics diagnostic computer to pin point the problem. Sometimes, you can clean the mass air flow with a special cleaner to help it generate a more accurate reading.

Apr 20, 2010 | 2001 Toyota Tacoma

1 Answer

IAT Sensor


it is part of the mass airflow sensor

Jun 19, 2009 | 2004 Toyota Tacoma

2 Answers

Air Fuel Sensor on a 2001 Toyota tacoma


4 cylinder: one air-fuel sensor (on the pipe after the manifold) and one oxygen sensor after the catalytic converter

6 Cylinder: two air-fuel sensors (one for each manifold) and one oxygen sensor after the catalytic converter.

Dec 29, 2008 | 2001 Toyota Tacoma

Not finding what you are looking for?
2001 Toyota Tacoma Logo

458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8729 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...