Question about 2004 Chevrolet Express

1 Answer

No light on my instrument panel cluster. Can I change a fuse or light bulb myslef?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

You sure can.

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No instrument lights


do taillights?fuse is blown for running lights,and check bulbs they go in bunches,if none of these are bad the printed circuit is bad on cluster,clusters are easy to change,youtube has instructions,buy it from ebay

Feb 19, 2014 | 1998 Chevrolet S-10 Pickup

2 Answers

NO LIGHTS ON LEFT SIDE OF ODOMETER PANEL - FUSE OR MAJOR WORK?


fuse ok.need to remove instrument cluster and see if good connection on the cluster os maybe yo can see a break in plastic circut board.I would have another instrument cluster handy if old unit not repairable

Feb 12, 2011 | 2001 Toyota Camry Solara

1 Answer

Instrument cluster bulb is out. how do i replace


It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Dec 22, 2009 | 2001 Chrysler Sebring

2 Answers

Check engine light does not turn on at all


The bulb is probably loose and/or burnt out. If you are mechanically inclined you can tackle this job... This procedure is the one i use, most often it's the blue high beam indicator bulb that goes so if you want to change it while your in there.....(hint hint)
Disconnect and isolate the battery negative cable. Wait a good 2 minutes to allow for air bag deactivation...NOTE: USE CAUTION ...Lower the tilt wheel to lowest position.
Remove the cluster bezel from the instrument panel.
Remove the two screws that secure the upper mounting tabs of the instrument cluster to the underside of the instrument cluster hood formation of the instrument panel top pad.
Remove the two screws that secure the lower mounting tabs of the instrument cluster to the instrument panel structural duct.
Pull the upper mounting tabs of the instrument cluster downward, then pull the instrument cluster rearward far enough to access the instrument panel wire harness connector for the instrument cluster. Disconnect the instrument panel wire harness connector for the instrument cluster from the connector receptacle on the back of the instrument cluster housing.
Remove the instrument cluster from the instrument panel. Now do you remember which bulb it was? You can now see where the check engine light bulb is mounted. Twist and remove, install in reverse order. In some cases they are just loose or not making good ground, but after going through this just to access that lil bugger, i'd replace it.
I hope i have helped you and if you feel i have please acknowledge.
Be well and keep the cherokees alive....

May 13, 2009 | 2001 Jeep Cherokee

1 Answer

Changing instrument panel light bulbs


You have to remove the entire cluster assembly to get to the bulbs, there is no other way, no room for this man's hand at the back.

Nov 09, 2008 | 2005 Dodge Caravan

1 Answer

Gas gauge no longer works


The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

May 14, 2008 | 2007 Jeep Scout

Not finding what you are looking for?
2004 Chevrolet Express Logo

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...