Question about Ford Escape

Open Question

Hi i have a 1999 ford galaxy 2.8v6 and i need the torque settings for the cylinder head can you help?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

dcramer531
  • 1654 Answers

SOURCE: I need the torque settings for the cylinder head

http://www.autozmagz.com/isuzu/2000-isuzu-trooper-s-torque-specifications/
try here and see if they can help. You can download manuals for free here.

Posted on Nov 23, 2010

  • 1 Answer

SOURCE: golf iv 1.6 8v cylinder head torque settings

Hi the title says 1986 is the correct

Posted on Mar 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

What is the cylinder head bolts torque setting for a ford fiesta 1999 1.25?


Hello friend,
Copied from here
http://www.fordownersclub.com/forums/topic/6527-fiesta-zetec-125-tourqe-settings-help/

You will have to use an online converter from Ft/lbs to Nm if you want Imperial.

'the sequence is as follows...

8 - 6 - 1 - 3 - 9
10-4 - 2 - 5 - 7

STAGE 1: tighten to 15Nm
STAGE 2: tighten to 30Nm
STAGE 3: tighten 90 degrees

the camshaft carrier/capa are tightened to 15Nm.'

Sep 11, 2014 | Cars & Trucks

1 Answer

Need to know Torque setting's for 96 Ford fairmont 4.0i cylinder head


You can call the Ford dealer service department. They can answer that for you.

Jan 21, 2013 | Ford Taurus Cars & Trucks

1 Answer

Torque specs for 99 f350 head bolts on 5.4l


Check this information for 1999 FORD TRUCK F350 SUPER DUTY P/U 4WD 5.4L EFI 8CYL and keep in mind that cylinder head bolts must be replaced with new ones. They are torque-to-yield designed and cannot be reused.

Tighten the cylinder head bolts in the sequence shown in three steps, as follows:
  1. Step 1-27-31 ft. lbs. (37-43 Nm).
  2. Step 2-tighten an additional 85-95 degrees.
  3. Step 3-tighten another 85-95 degrees.

12_19_2011_7_03_40_pm.gif

Image Zoom Link : large/0900c152801e5215.gif

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day

Dec 19, 2011 | Ford F-250 Cars & Trucks

3 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

1 Answer

Hi i need the torque setting for ford escort p reg cylinder head and cam bearing can you help


hi the cylinderhead torque settings are
STAGE 1, 30Nm (22l bf ft)
STAGE 2, 50Nm ( 337 lb ft ),
STAGE 3, angle tighten another 90 degrees,
STAGE 4 angle tighten another 90 degrees

Cant help you with the cam bearing though sorry

Dec 17, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...