Question about 1996 Honda Accord

1 Answer

Removing cv joint from trans - 1996 Honda Accord

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,455 Answers

You have to pry it away from where it enters the transmission, with a suitable tool.

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cv joint popping out right front


The CV Joint would have to come out, take the boot out. The cv joing is probably coming out of the end. There is like a washer that holds it in place and is possible that is out of place.
I hope this helps!

Mar 26, 2013 | 2003 Ford Escape

1 Answer

CV boot leaking


get a boot replacement kit remove axle from suspension and trans. clean old grease out of failed axle, stuff new grease into cv joint and put new boot on shaft close to joint. fill the boot with the rest of the tube of cv grease and install per instructions.

Nov 03, 2012 | 2003 Subaru Baja

1 Answer

2005 KIA SEDONA OUTPUT SHAFT SEAL


Hi Phil, On the Spyder end of the shaft that fits into the gearbox there is a retaining clip. Did you knock it in securely? If you did then a seal may have become damaged when making the replacement. That will need replacement. Regards John

Oct 27, 2012 | 2005 Kia Sedona

1 Answer

How to change a Cv joint on a 1997 Pontiac Grandam


While the car is still on the ground remove the half shaft nut then jack the car up and support it with jack stands and remove the tire. after you get the tire off you may have to remove the break caliper and the rotor, if you have to do this now. Remove the lower ball joint nut and break apart the ball joint with a large pry bar by prying down on the lower a frame. grab the steering knuckle with both hands and pull until the half shaft is free from the bearing hub assembly. then grab the half shaft and give it a good tug to remove it from the trans axle, you may have to pry it out with a small pry bar wedged between the inner cv joint and the trans axle. at this point I would replace the entire half shaft it is cheaper and a lot easier than replacing the cv joint. installation is reversed but be careful of the splines when installing the half shaft back into the trans axle and the bearing hub. Good luck.

Nov 02, 2010 | 1997 Pontiac Grand Am

1 Answer

Need diagram on what has to be removed to replace the driver side trans axle


Not much to it,
remove wheel,remove axle nut,remove bolt and nut that pinch lower ball joint in place,it will either be an 18mm or a 21mm,pry lower control down to detach and separate ball joint,tap CV shaft in where you took the nut off,
hold out on rotor assembly while pushing CV shaft in ward,When you have the CV out of the bearing and rotor assembly,Tap inside CV joint out of transmission.

Dec 16, 2009 | 1996 Plymouth Grand Voyager

1 Answer

Installing cv axle on a 2004 impala


remove the tire, remove caliper and rotor remove 35mm nut and push cv joint into trans and remove

Sep 20, 2009 | 2004 Chevrolet Impala

1 Answer

How do you remove the CV joint from the drive axle


remove the tire rotor and some other stuff unless you whant to take out the trans these are the to way you can do it

Aug 16, 2009 | 2006 Volkswagen Passat

1 Answer

Need instructions to replace front passengers side cv joint


Do yourself a favor and replace the whole cv shaft. Quicker, eaiser and not much money. First get the car in the air and remove the wheel. Then pop the lower ball joint. This is done by unbolting it from the knuckle and using a ball joint seperator fork and a hammer. Then remove the spindle nut on the end of the cv shaft. You push down on the lower A arm pulling the ball joint out of the knuckle and push the cv shaft out of the hub. Once these are dislogged, you can movel the strut and hub out of the way and pull the cv shalt out of the trans axle. Push the new one in and reverse what you did.

Aug 08, 2009 | 1996 Chevrolet Cavalier

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

3 Answers

Cv joints


Definitely not easy.You need a way to jack the front end and support it safely.Have to use a pretty powerful 1/2" drive air gun as a couple hundred foot pounds is required to remove the axle nuts,as well as a large socket to fit the axle nut.You also have to break the ball joints loose,and have a large pry bar to remove the axles from the trans while being careful of the axle seals.

Jul 14, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...