Question about Buick LeSabre

1 Answer

Wires are covered on top of the engines. I don't see any bolts to remove the cover. Does it just pop off ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,702 Answers

Yes, remove the oil fill cap and short pipe and then the cover will just pull off.

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I aquired a 94 gran am se 2.3 engine. funny thing about this car, i can't find any spark plug wires or spark plugs. there's a sticker under the hood that says the gap on them. where would they


you have to remove the top cover of the motor...the silver part that quad 4 on it they are under there, I don't remember how many bolts there are but that's where they are !

Jun 11, 2012 | 1994 Pontiac Grand Am

1 Answer

Check an ignition coil pack for aura 3.2 TL






ironfist109_390.jpg




  • For coil wires.

  1. Remove the intake cover.
  2. Remove the right side engine cover - A -
  3. Remove the left engine cover - B -
  4. Remove Right rear engine cover - C -
  5. To remove the #6 coil you will also need to remoce the heat shiel off th reserve tank and the reserve tank as well.


  • For coil pack.

  1. Remove negative battery cable
  2. Remove engine covers show in diagram.
  3. Remove the coils (listed above).
  4. Now just remove the mounting bolts to the coil packs.

  • Please Note - Don't loose the firing order of your car will not run.

  • Here is a spare one in case you get mixed up.
  • Firing order is
  • 1-4-2-5-3-6



ironfist109_391.jpg



  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 13, 2011 | 2002 Acura 3.2TL

2 Answers

Where on spark plugs and wires on 99 - 4 cyl. Malibu w/ overhead cams


pull the cover that has the 4 bolts in it on top of the engine. that is the coil/ignition module housing. the plugs are under it along with plug boots that you may want to replace.

Jul 25, 2011 | 1999 Chevrolet Malibu

1 Answer

Removal of plug wires on 2000 Chev silverado


Underneath the hood is the engine.On top of the engine is a big plastic cover, cover entire top of engine.
Example: http://image.trucktrend.com/f/8511504/112_0507_02z_2005_chevrolet_silverado_ss_pickup_engine.jpg

Remove the cover by taking out the bolt/screws on the top of the cover.
Once removed the plug wires are clearly visible.
Take pictures or mark where the wire are plugged into.
One at a time!!! remove one wire and replace it with a new one.
Put it back together

May 30, 2011 | 2000 Chevrolet Silverado 1500

2 Answers

I can't figure out how to remove the shifter from my 1991 ford f150, 4.9 liter manual transmission.


Remove the rubber mat or carpet from the floor around the shift tower. This will expose a stamped steel plate that you can remove to get access to the top plate of the transmission. Place the transmission in neutral and remove the bolts securing the top cover to the tranny. After removing the bolts you may need to use a rubber mallot to bump loose the cover. Pick the cover straight up and out. After removal cover the hole with a rag or better yet fabricate a cover from a thin piece of plywood that you can bolt back in place with a couple of bolts to prevent dirt and foreign particle from entering the tranny. When you remove the top cover and see the forks hanging from the underside don't worry. When you place the cover back onto the tranny just line up the shift forks to the slots they drop into on the gears. Piece of cake.

May 11, 2011 | Ford F-150 Cars & Trucks

2 Answers

I cant find the spark plugs on my 1991 kia sportage


If your sportage has the 4 cylinder engine, there is a plastic cover over the engine that is held down by 4 bolts, one at each corner. Remove the bolts with a 10mm socket and lift he cover off and lay it aside. You will see the spark plug wires and the 4 holes where the spark plugs are. The spark plugs are about 4 inches down into the holes. Be careful removing the spark plug wires, they will be tight, and you will have to rotate them back and forth while pulling up to get them loose.

Jan 02, 2011 | 1998 Kia Sportage

1 Answer

Where are the spark plug wires located on a 1995 grand am quad 4? Also how do you access the plugs?


This car has no plug wires. On the top of the engine you will see a cover that says twin cam.. There are four bolts in this cover. Remove the 4 bolts then gently work the cover back and forth while pulling up on it. It will lift up. The plugs are underneath this cover on top of the engine.

May 14, 2010 | 1995 Pontiac Grand Am

2 Answers

Where are the spark plug wires located on a 1995 grand am quad 4? Also, how do you access the plugs?


The Quad 4 does not have plug wires. The engine cover plate has 4 bolts. remove them and lift straight up on the cover. the sparkplug boots will come up with the cover plate. They are protruding strait down from the coils(4) and the plugs are down in the valley between the cam towers if you have the DOHC or behind the cam tower if you have the SOHC.

Mar 23, 2010 | 1995 Pontiac Grand Am

2 Answers

2.4l santa fe spark plug location


there are 2 covers that are over the plugs the first is the big silver and black cover that has four
10mm bolts remove them and then there is a small black cover that is inbetween the two humps on the valve cover i think that there 6 bolts that holdthat down remove this and the coils and plug wires are visable

Apr 12, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...