Question about Mercury Mariner

Open Question

I need a fuse panel layout for a 2006 Mercury Mariner 4 cylinder

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 130 Answers


Download and go to page 153.

Posted on May 06, 2009

  • 1596 Answers

SOURCE: what tool do i need to replace front brake pads on 2008 mariner?

You Will Need A 13-14 mm Wrench for Caliper Bolts .A Large Flathead Screwdriver to Spred open Caliper/Shoes to Remove Caliper from Rotor,
After rhis you Can use a LARGE "C" Clamp to CLOSE Caliper Piston.

Posted on Nov 06, 2009

  • 17970 Answers

SOURCE: I need the interior fuse panel layout. Keep

Ford Full-Size Vans 1989-1996 Repair Guide
The fuse panel is located on a bracket on the driver's side of the instrument panel or, on some RV models it is located on a bracket attached to the brake pedal.


The fuse panel is located on the driver's side of the of the van, below the instrument panel


Typical power distribution box, which is located in the engine compartment

I hope this helped (remember rated this help) Good luck.

Posted on Dec 14, 2009

  • 131 Answers

SOURCE: how to I change the right tailight on my 2006

Open the liftgate and remove the 2 screws holding the lamp. Now grab the lamp and pull straight back to dislodge the spring clips. Then twist the sockets to remove the bulbs.

Posted on Mar 17, 2010

  • 1 Answer

SOURCE: replace alternator on 2005 mercury mariner

change alternator on a 2005 mercury mariner 2wd with a v6

Posted on Jul 10, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006 Merc Mariner 4-wheel drive indicator continuously flashes.

This means there is a fault in the 4X4 electronic control system. The dealer needs to hook up a special scan tool to see what the fault is.

Apr 04, 2017 | 2006 Mercury Mariner

2 Answers

I have a 2OO6 Mercury mariner and I wanting to know what fuse do I change cause my heat/air panel light want work.

And what if the heat air panel is defect? Or has a bad connection, or return? Lose wire? Try to find out what is wrong before you look for a fuse. Use a multimeter and see where you still have power and where not.

Mar 09, 2015 | 2006 Mercury Mariner

1 Answer

What fuse location does the Auxiliary Power Point use on a 206 Mercury Mariner?

Assuming your Mariner has a V6 and is not a hybrid, 20A FUSE 12 in the battery junction box (BJB) supplies 12 volts to the power point.

Sep 21, 2014 | 2006 Mercury Mariner

1 Answer

2005 mercury mariner 4 cyl. starts then stalls, won't restart for prolonged rest period

did you use fuel addetive to stop fuel in carbs going off when you laid it up and winterize the cylinders etc ? check compressions , sparks and fuel is in all carbs as if you have sparks then carbs need stripping and cleaning ie, jets and float needles ! compressions to be no less than 100 psi on all 4 cyls !

Jan 14, 2014 | 2005 Mercury Mariner

1 Answer

I have a 2006 mercury mariner and the reverse lights do not come on, new bulbs were put in , fuse look good

there is a reverse switch that semds the voltage to the back up lights,, yours is either stuck, or bad.

Sep 09, 2011 | 2006 Mercury Mariner

1 Answer

2006 mercury mariner 3.0 will trun over but will not start . it is getting spark and gas

is its timing set right... eg: does it spark when piston isjust about at top dead centre? for every cylinder?

Mar 01, 2011 | 2006 Mercury Mariner

1 Answer

My rear break lights and turn signals have stopped working on my 2006 Mercury Mariner. I have replaced the rear bulbs and fuses which hasn't fixed the problem. The lights on the front work fine. A mechanic...

There is two different Flasher Relay's for the 2006 Mariner.

With Towing Package: Part # YL8Z13350AA or SF620 (Around $45 online)
Without Towing Package: Part # YL8Z13350BA or SF621 (Around $60 Online)

Dec 27, 2010 | 2006 Mercury Mariner

1 Answer

4 cylinder oil capacity

Most 4 cylinder engines have a capacity of between 4 and 5 liters.
I would put 4 liters in , run the engine for a minute or two , wait a couple more minutes for the oil to drain back down into the oil pan , and then check the dipstick. Vehicle should be on reasonably level ground to get and accurate dipstick reading.

Oct 18, 2010 | 2006 Mercury Mariner

1 Answer

Need location of 2006 mercury mariner security module to get keyless door pad code

I have a 2006 Ford Explorer and I just found my keyless entry module. The module was behind the lower plastic panel on the passenger side rear panel right below the seat belt height adjuster. Not the panel with the seatbelt adjuster but the one below it. No tools were needed and it took me all of 5 minutes. Just pop off the front of the panel closest to the door and pull it back. Use a light and you can see the large 5 digit code on top of the module. Thanks very much to the people that contribute to this forum....Cheers
This is really where it is!

Nov 12, 2009 | 2006 Mercury Mariner

1 Answer

2006 Mercury Mariner

it could be frozeup or blew an outlet valve have some one check coolant levl for the a/c

Sep 01, 2008 | 2006 Mercury Mariner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

75817 Answers


Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides