Question about Oldsmobile Cutlass Supreme

1 Answer

Looking to replace head gasket for a 1971 oldsmobile cutlass supreme. need to know the pressure to put back in and also if there is any special order to the bolts when installing.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

You can buy a Clymers or Chilton manual with the torque specs. and the tightening order. Generaly the bolts are tightened from the center outwards in two steps. First pass you snug all the bolts down, working from the middle bolts outward to the front and rear alternating between left and right side bolts.

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my 95 oldsmobile cutlass supreme dies when hit gas


Did you replace the fuel filter as well as the oil filter ?. If there is a good spark at the plugs it has to be a fuel problem . Check the fuel pressure and flow the flow is most important. if the pressure is high the regulator on the fuel rail may be stuck shut . and there will be no flow on the return line.

Aug 16, 2014 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Intake manifold back two ports block is that normal for 83 cutlass supreme 3 8


yeah. Some people block them off whe they are swithching the pipes from single to double or vis versa

Oct 26, 2011 | 1983 Oldsmobile Cutlass Supreme

2 Answers

Car low coolant light on, over heated , fans didn't work. REPLACED: straight wired fans, fans worked. end up changing cool temp. sensor,crank cover broke replaced put in new CTC,radiator cracke,...


sounds like blown head gasket in between cylinders,that isnt supposed to push out fluid,most likely blown head gasket,check with another mechanic u trust,take car back

Jul 22, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

I put knew head gaskets on 91 3.1 olds cutlass supreme and it cracks but wont start


ok do you have spark? do you have fuel? this is where i would start. if you have both i would check and make sure you put the pushrods in the right place.

Oct 22, 2010 | 1991 Oldsmobile Cutlass Supreme

1 Answer

Where are the gaskets on a 1994 oldsmobile cutlass supreme


valve covers,1/2 hour each, oil pan 1 hour,head gaskets 7 hours,transmission pan1 hour ,intake 5 hours,or exhaust manifold gaskets.4 hours

Oct 23, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1971 Olds Cutlass Supreme. Dash brake light stays


They are unrelated. Just make sure your brake release is fully relesed. The switch turns the light on if the release isn't against it fully.

Jul 14, 2009 | Oldsmobile Cutlass Cars & Trucks

3 Answers

Wather in the engine oil , oldsmobile 1995 cutlass supreme


If there is water in your engine oil or it looks like chocolate milk, then you have a blown head gasket. Your coolant will also be off color and your car will most likely begin to overheat. It will be need to be repaired.

Jul 06, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...