Question about Chevrolet Lumina

1 Answer

Will not hold belt and tighten - Lumina Chevrolet Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 90 Answers

Thread is stripped by the sound of it.

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tighten alternator belt on 1993 pathfinder


Four cylinder engine - loosen bottom pivot bolt on alternator, then loosen top bolt and pull the alternator away from the engine to tighten belt. When at proper tension, tighten top bolt to hold tension and tighten bottom pivot bolt.
Six cylinder engine - loosen the lock bolt at the bottom of the alternator, then use the adjustment bolt (perpendicular to the lock bolt) to tighten the belt tension. Once properly tensioned, tighten the lock bolt.

Jan 30, 2017 | Cars & Trucks

1 Answer

I replaced the idler pulley in my car,The bolt that secures the pulley to the tenioner won't lock but tightens.I can get no leverage to get belt on? Any suggestions with out replacing tensioner arm


you don't lever belts at all as it breaks the bindings in the belt
the nut on the shaft that holds the pulley on has to be loosened and then the small bolt at the back of the tensioner mount will move the pulley shaft up or down to adjust the belt tension
so move the pulley shaft to the point where the belt just slips into the pulley groove and then tighten the bolt up until tension is on the belt
tighten up the nut holding the pulley on
If you have the spacer s in the right position then that nut will tighten up securely and retain the tension on the belt

Oct 10, 2015 | Cars & Trucks

1 Answer

How to tighten the altanator belt on a 1983 chevy cavalier


It's alternator. Do you have a serpentine belt or seperate belt. If seperate, there are two bults on the alternator. Loosten both but do not remove. Take a prybar and pry back on alternator. Have someone hold the prybar while you tighten or hold yourself and tighten. If you have a serpentine belt, you need to replace the belt tensioner. The spring is weak inside the tensioner. It's 30 years old. remember that.

Jan 25, 2013 | 1983 Chevrolet Cavalier

1 Answer

Tighten alternater belt


Loosen the altenater and use a prying bar to tighten the belt by pushing the altnater so as to tighten the belt. while holding altenater in place tighten bolts back tight. Belt should be tight when finished.

Feb 25, 2011 | 1994 Nissan Altima

1 Answer

There are 3 belts on the truck. The belt that goes around the alternator is not spinning. What could cause this belt not to turn?


Assuming that the belt is not broken ... you need to tighten the belt. This one is not as easy as the other two which have tensioners. This belt is tensioned by the alternator itself. I've found adjusting it to not be a lot of fun ... the tricky part is loosening the bolt that the alternator pivots on. There isn't a lot of room and I find one of the small palm ratchets to be helpful. So to tighten, you'd loosen the upper bolt that actually holds the tension on the belt, loosen the bolt that the alternator pivots on, re-tension the belt (using something to pry on the alternator if necessary) and tighten the two bolts again. If you have to replace the belt you'll need to remove the outer two to get to this one. The outer two tensioners are adjusted by loosening the bolt that holds the tensioner pulley in place and then turning the tensioner bolt itself to tighten or loosen the belt(s)... then retighten the bolt holding the pulley.

Feb 08, 2011 | 1994 Toyota Pickup

1 Answer

How do i tighten the belt that goes around my alternator


You will need ratchet and socket set, something to help hold the alt.(alternator) when tightening the belt ( like a pry bar). Loosen the bolts around the alt.. now it will move, and you need that prying tool now. use it to move the alt. so the belt has about an eighth of an inch of play. holding it there, tighten the bolts back (nice and snug). Never over tighten the bolts, they can snap on you. now start the car, and you should see the belt is not slipping any more. This job will take you about 20 to 30 minutes.

Dec 29, 2010 | 1985 Nissan 300ZX

1 Answer

How can I tighten the alternator belt?


loosen the bolts for the alternator, then lever the alternator away from the block to tighten the belt.you have 2 bolts holding the alternator and 1 holding the adjusting arm.(loosen both ends/lever/then tighten)

May 27, 2010 | 1993 Toyota Corolla

1 Answer

How do i tighten a loose screeching belt on an '01 accent gs 1.6L


The belt is adjusted by the position of the alternator. Loosen the bottom mounting bolts. Loosen the adjusting bolt in the top bracket & using a suitable lever, pry the alternator outwards until the belt is tight. Do not tighten it too tight. you should be able to deflect the belt down about 3/4 -1" when tightened. Hold the bar to maintain this tension on the belt and tighten the top adjusting bolt. Re-tighten the two bottom bolts. Check the deflection of the belt once more to ensure it is not to tight.

Mar 21, 2010 | 2001 Hyundai Accent

1 Answer

Fanbelt


MORE INFORMATION NEEDED. There are several deices to adjust belts. On serpentine belts there is a tensioner pulley that should hold spring applied pressure on the belt. If that doesn't work it needs to be replaced. On some engines it is tightened by adjusting an idler pulley. On some it is accomplished by adjusting the alternator or power steering pump. Look to see which part has an adjustment and loosen the nut or bolt holding it, move the part to the desired tension and tighten the nut or bolt.

Dec 15, 2009 | Cars & Trucks

1 Answer

How do i put on a new fan belt on a 2000 golf tdi?


Well for the fan belt its really simple: You need: a 13mm Socket, a 6mm Hex bit, and a ratchet, a large crescent wrench would also be helpful.
1. Loosen the 6mm bolt that holds the alternator in.
2. Loosen off the 13mm bolt that is on the bracket.
3. Take the old belt off.
4. Put on the new belt.
5. Slightly tighten the 13mm bolt, and use the crescent wrench to tighten the belt (using the half gear/half nut tightening assembly)
6. Tighten the 13mm.
7. Tighten the 6mm.

Sep 28, 2009 | 2000 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...