Question about Ford Mustang

1 Answer

I am a owner of Ford Mustang V6 2006 Coupe.My problem is with my reversing lamp signal I have all the Time the signal with out to use the reverse gear in both side The turn the lamp is on all the Time pls i need Help Thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 257 Answers

There is a switch, usually on the side of the transmission next to the shifter linkage, that turns the backup lamps on. My guess is yours is stuck. Sometimes you can free them up, but it will stick on again, or fail all together, so your best bet is to get a new one from the parts store, and then you will know exactly what the old one looks like.

Posted on Mar 14, 2011

Testimonial: "Fast Answer. Thank you :-))"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a trick to getting to the rear turn signal on a 2003 ford focus hatchback. I had removed the screw to the lens cover but I still cannot gain access to the turn signal bulb to replace it.


Replacing tail/brake/backup lights and turn signal bulbs (coupe)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. From inside the luggage

compartment remove the wing nut

of the rear light assembly cover.

3. Using a Phillips screw driver

remove the screw. The lamp is still

retained by a spring loaded clip.

Remove by gently pulling out the

light housing.

4. Turn the bulb socket counterclockwise as far as possible and pull it

out.

5. Pull the bulb straight out of the socket.

Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (sedan)

1. Make sure the headlamp control

is in the OFF position and then

open the trunk.

2. From inside the luggage

compartment remove the three wing

nuts of the light housing.

3. Gently pull the light housing to

the outside.

4. Turn the bulb socket

counterclockwise and pull it out.

5. Pull the bulb straight out of the socket.
Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. Using a screw driver remove the

fixings and trim from the body.

3. Remove the socket from the lamp

assembly

4. Pull the bulb straight out of the

socket.
Install in reverse order.


Hope this helps.

Zeppelinx12

Mar 03, 2011 | 2003 Ford Focus

1 Answer

I need to replace rear tail light bulbs on 1996 Saturn SL1


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif

Oct 23, 2010 | 1996 Saturn SL

1 Answer

The button on the side of the gear shifter will not go in to change from park to reverse. \r\n2005 Ford Mustang


check your stop light working or not, if not check fuse and the stop light switch, if all ok, check the reverse lock-out solenoid, check out your owners manual to lock out manually

Jun 18, 2010 | 2005 Ford Mustang

1 Answer

1966 mustang coupe motor 289,4 barrel carb.automatic trans. makes a noise when put in reverse,is this normal?


What kind of noise? A clunk, chatter, whir, grinding, or what? If it's a clunk, you may have a worn U-joint. Test by holding brake on and change between drive and reverse and back. If you hear a "clunk" when the tranny engages, it's probably a worn U-joint. Not a hard repair to do in the driveway. Always change BOTH front and rear U-joints - if one's worn, so's the other.

Oct 28, 2009 | 1966 Ford Mustang

1 Answer

Fuse number for the wipers: 2002 mustang gt coupe


Onlinefreebooks.net has owner's manuals that can be downloaded. The owner's manual will have that location in it.

Oct 14, 2009 | 2002 Ford Mustang

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

Lighting


Hey rhyeese,
Theres one more thing you can try.
Locate the gearbox, there should be a wire either hanging or not connected properly, connect that as it is the reverse sensor. This sends a signal to your lights as soon as you pop it into reverse.
Hope this helps.

Apr 08, 2009 | 2002 Ford Mustang

1 Answer

Interior lights


What they are speaking of is the GEM module however this will not correct the concerns you have.
The GEM controls the following functions:
  • warning chimes and warning lamps
  • one-touch down window
  • windshield washers and wipers
  • battery saver
  • illuminated entry with keyless remote entry
  • interior lighting
Turn signals and hazzard lamps do not go thru the GEM module at all and the reverse lamps all the gem does there is look for reverse so it knows when to activate the auto lock doors when vehicle is in motion.
I suspect you have 2 or more problems here that you may want to get checked by an experienced Ford tech.Also the GEM has to be programed when replaced.It is not plug and play.

Feb 02, 2009 | 2002 Ford Mustang

1 Answer

How do I set the clock on my 2003 Ford Mustang 2 door coupe


Here is a link to your owners manual at Fords web site, download it and look on page 22 for the procedure to set the clock.

http://www.motorcraftservice.com/pubs/content/~WO3MUS/~MUS~LEN/42/03musog5e.pdf

Oct 21, 2008 | 2003 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...