Question about Mercury Tracer

1 Answer

Electrical - Tracer Mercury Cars & Trucks

Posted by on

  • Anonymous Mar 25, 2009

    i have the same problem with my 1999 volvo headlights will not stay on work sometimes and than they stop working

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

HEAD LIGHT SWITCH BLOWS FUSES

Posted on Feb 03, 2009


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 grand marquis the door lock and the trunk button quit working


If you want to fix this yourself your going to need to develop some kind of electrical diagnostic skill's . Finding wiring diagrams at www.bbbind.com . watch videos on youtube for basic electrical testing . You'll need to buy a DVOM - digital volt ohm meter . Electrical Series Tools Theory Of Auto Electrical Diagnosis and Repair Electrical Troubleshooting Basics EricTheCarGuy It mite be best for some people to just take it to a qualified repair shop .

Oct 02, 2016 | 2002 Mercury Grand Marquis

2 Answers

Name the colored wires


Fred, Charlotte, Agnes...........

Nov 24, 2015 | Cars & Trucks

1 Answer

Why don't tail lights work when fuses have all been changed?


Because it wasn't the fuse's . You have an electrical problem . Find a wiring diagram an do some electrical circuit trouble shooting . Go to youtube an watch some videos on basic electrical trouble shooting .Or the smart thing to do would be take it to an automotive electrical repair shop .

Nov 21, 2015 | Cars & Trucks

1 Answer

How do I remove the engine fuse box in a 2003 Malibu? Where is the removal clip located?


Removal Procedure
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls.
  3. Remove the nut retaining the positive battery cable lead to the underhood electrical center, then reposition the cable lead away from the electrical center.
  4. Remove the electrical center cover.
    showgif.do?image=736009
  5. tif.gif
  6. Remove all of the fuses and the relays.
    showgif.do?image=736049
  7. tif.gif
  8. Reach under the front of the electrical center and press up on the relief in order to release the retainer tab.
  9. While pressing up, slide the electrical center forward.

Jan 22, 2015 | 2003 Chevrolet Malibu

1 Answer

Where is the throttle position sensor on my 2004 4.2


S&T Series Blazer, Bravada, Envoy, Jimmy, Rainier, Trailblazer, Xtreme
Throttle Position Sensor (TPS)

Print


Removal & Installation

  1. Remove the idle air control (IAC) electrical connector (1) from the IAC sensor (4).
  2. Remove the manifold absolute pressure (MAP) sensor electrical connector from the MAP sensor.
  3. Remove the water pump belt cover.
  4. Remove the TP sensor retaining screws electrical connector (2) from the TP sensor (3).
  5. Remove the TP sensor electrical connector (2) from the TP sensor (3).

    0996b43f80202874.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Detaching electrical connectors prior to TP sensor removal


    0996b43f80202875.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Identifying components for removal of the TP Sensor


To install:
  1. Install the new O-ring on to the TP sensor.
  2. Connect the TP Sensor electrical connector (2) to the TP sensor (3).
  3. Install the TP sensor (2) on to the throttle body (1). Tighten the TP sensor screws to 2.3 Nm (20 inch lbs.).
  4. Connect the IAC electrical connector (1) to the IAC sensor (4).
  5. Connect the MAP sensor electrical connector to the MAP sensor.
  6. Install the water pump belt and tensioner cover.
  7. Perform the TP Sensor learn procedure:
  8. Turn the ignition to the RUN/ON position.
  9. Wait 1 minute.
  10. Turn the ignition to the LOCK/OFF position

Jul 31, 2012 | 2004 GMC Envoy

1 Answer

How do you replace the throttle position sensor


Removal & Installation
  1. Remove the idle air control (IAC) electrical connector (1) from the IAC sensor (4).
  2. Remove the manifold absolute pressure (MAP) sensor electrical connector from the MAP sensor.
  3. Remove the water pump belt cover.
  4. Remove the TP sensor retaining screws electrical connector (2) from the TP sensor (3).
  5. Remove the TP sensor electrical connector (2) from the TP sensor (3).


57f7d68.gif

Detaching electrical connectors prior to TP sensor removal



6244f87.gif

Identifying components for removal of the TP Sensor


To install:
  1. Install the new O-ring on to the TP sensor.
  2. Connect the TP Sensor electrical connector (2) to the TP sensor (3).
  3. Install the TP sensor (2) on to the throttle body (1). Tighten the TP sensor screws to 2.3 Nm (20 inch lbs.).
  4. Connect the IAC electrical connector (1) to the IAC sensor (4).
  5. Connect the MAP sensor electrical connector to the MAP sensor.
  6. Install the water pump belt and tensioner cover.
  7. Perform the TP Sensor learn procedure:
  8. Turn the ignition to the RUN/ON position.
  9. Wait 1 minute.
  10. Turn the ignition to the LOCK/OFF position.

May 12, 2010 | 2000 GMC Jimmy

1 Answer

B200, 2006 cvt trany,starter doe,s not crank at all every once in a while, battery ok, connections et ground ok. the scanner tell,s us starter is defect. I dont have a wiring diagram so i have to figure...


You can electrical supply directly from plus battery to electrical starter solenoid.
For that you must prepar an electrical wire. One end connected at the electrical starter solenoid, and another end directly on plus battery. If electrical starter crancks the problem is on electrical supply. If doesn't cranks then electrical starter
is out of order and must be removed from engine and repaired! The most frequent problem of electric starters are carbon brushes used!
Did you try this operation?

Jan 14, 2010 | 2006 Mercedes-Benz B-Class

1 Answer

Dashboard lights burning out, down to 1 illuminating tach, speedo, gas gauge. How complicated to replace?


one hour job. find bulb part number in bulb chart in owner manual.

go here for villager help.

http://groups.yahoo.com/group/villagerquest/

Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
-------------------------------------------------------------------------------------------------
Instrument Cluster
Removal
  1. Disconnect the battery ground cable (14301).
  1. Block the wheels (1007) to prevent the vehicle from moving.
  1. Turn the ignition switch (11572) to the OFF position.
  1. Shift the transmission range (TR) selector to MANUAL LOW (1).
  1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
  1. Remove the two instrument panel finish panel screws.
  1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
  1. Disconnect the rear windshield wiper/washer switch electrical connector.
  1. Disconnect the heated back window and light switch electrical connector.
  1. Disconnect the emergency warning switch electrical connector.
  1. Disconnect the SECURITY indicator light electrical connector.
  1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
  1. Disconnect the headlamp switch electrical connector.
  1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
  1. Remove the instrument panel finish panel with the switches attached.
  1. Remove the four instrument cluster screws.
  2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).

Jan 13, 2010 | 1995 Mercury Villager

1 Answer

Need help with dash removal.


  1. Remove the A-pillar and cowl side Trim Panels
  2. Remove the front floor console.
  3. Depower the supplemental restraint system (SRS).
  4. Remove the instrument panel side finish panels.
  5. Remove the 2 steering column opening cover screws.
  6. Remove the steering column opening cover.
  7. Remove the 3 lower steering column cover screws.
  8. Remove the lower steering column cover.
  9. Disconnect the steering column electrical connectors.
  10. Disconnect the RH side bulkhead electrical connector.
  11. Disconnect the RH side body harness electrical connector.
  12. Remove the 2 parking brake release handle screws.
  13. Disconnect the LH side instrument panel electrical connectors.
  14. CAUTION: To avoid damage to the clockspring, do not allow the steering column shaft to rotate while the intermediate shaft is disconnected.
  15. Remove the pinch bolt..
  16. Disconnect the adjustable pedal electrical connector.
  17. Disconnect the brake light switch electrical connector.
  18. Remove the 2 LH instrument panel center brace bolts..
  19. Remove the 2 LH instrument panel center brace nuts.
  20. Remove the LH instrument panel center brace.
  21. Disconnect the transmission range selector lever cable.
  22. Disconnect the RH side bulkhead electrical connector.
  23. Disconnect the LH side body harness electrical connector.
  24. Remove the 3 ground strap bolts.
  25. Disconnect the inertia switch electrical connector.
  26. Disconnect the RH side instrument panel electrical connectors.
  27. Remove the 2 RH instrument panel center brace bolts.
  28. Disconnect the vacuum connector.
  29. Remove the 2 RH instrument panel center brace nuts.
  30. Remove the RH instrument panel center brace.
  31. Remove the cowl panel grille
  32. Remove the instrument panel bolt located under the cowl panel grille
  33. Remove the instrument panel defroster grille.
  34. CAUTION: To avoid damage to the sunload sensor and electrical connector, remove the grille just enough to disconnect the connector.
  35. Disconnect the sunload sensor electrical connector.
  36. Remove the 2 instrument panel top cowl bolts.
  37. Disconnect the antenna lead-in cable.
  38. Disconnect the RCM electrical connector.
  39. Disconnect the center ground strap bolt.
  40. CAUTION:To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
      • Before removing the instrument panel make sure all electrical connector wiring is free and not hindered.
  41. Remove the 4 instrument panel bolts.
  42. Remove the instrument panel.
  43. To install, reverse the removal procedure.

Feb 11, 2009 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...