Question about 1995 Mazda Millenia

1 Answer

If the transmission is engage the engine would shake and you hear engine knock,but i put it on park or neutral the engine idle is smooth

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 277 Answers

Check your engine mountings and stabilizers.
Regards, DT

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What should my timing be set at for a 1989 nissan truck with the z24 motor


Ignition Timing 10 Degrees
Application:
With manual transmission

Note :
Before top dead center
*Warm idle speed 800 RPM
*Transmission in neutral (Parking brake engaged)
***CAUTION***
special procedures are required when making
adjustments
refer to service manual Ignition Timing 10 Degrees
Application:
With automatic transmission

Note :
Before top dead center
*Warm idle speed 750 RPM
*Transmission in drive (Parking brake engaged)
*All accessories off
***CAUTION***
special procedures are required when making
adjustments
refer to service manual.

Oct 15, 2014 | Nissan Cars & Trucks

1 Answer

Ignition timing



1991 Nissan/Datsun Truck D21 Truck 2WD 3.0L FI 6cyl

The Ignition Timing
15 Degrees Before top dead center*Warm idle speed 750 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

1991 Nissan/Datsun Truck D21 Truck 2WD 2.4L FI 4cyl

The Ignition Timing
10 Degrees Before top dead center*Warm idle speed 800 RPM*Transmission in neutral (Parking brake engaged)*All accessories off.

Mar 24, 2014 | 1991 Nissan Pickup

1 Answer

I have a 1999 Pontiac Sunfire. Transmission is going out I think. When I put it into reverse it's sometimes goes into reverse and sometimes doesn't but I hear a loud knock. fluid is right and not...


putting it into a gear and hearing a knock indicates that the engine mounts or transmission mounts are broken
naturally if you put it in neutral it will not move as that what neutral is
perhaps the neutral position needs adjusting as it may still be in drive
have the fault codes read to determine any sensor/servo/solenoid faults before spending big money on a transmission

Jun 29, 2017 | Cars & Trucks

1 Answer

Continued knocking while driving. Seems to knock faster as I accelerate, but does not knock at idle in neutral, starts to knock when reviving at 2200 rpms


Well lift the car up and put it on drive wile you can hear what the knock is. See if is your engine or the transmission. And if ok check your spark plugs make sure you getting fire to them

Feb 26, 2013 | 2001 Volvo C70

1 Answer

How to set timing on 87 isuzu pup truck replaced timing chain


6 Degrees
Application:
With automatic transmission

Note :
Before top dead center
*Set at warm idle speed (900 RPM)
*Disconnect & plug vacuum hose at electronic spark
control computer
*Transmission in neutral (parking brake engaged)
*All accessories off
and with a timing light loosen the dizzy or distributor and turn it till it runs smooth or at 6 degrees

Apr 07, 2010 | 1987 Isuzu Pickup

1 Answer

Was loping in drive, would have to put in neutral, now stalling in neutral, at first i thoght it was the fuel injector, not sure


engine runs smooth if giving more than idle pressure. It is when the motor is engaged with transmission at start the engine lopes and wants to cut off. If I press the throttle hard it takes right off. If I come to a stop I can put transmission in neutral to keep it from cutting off. This creates a shifting that is not normal and I'm afraid it is a sign of failure coming.

Sep 28, 2009 | 1990 Mazda 626

1 Answer

1995 NISSAN MAXIMA RUNNING POORLY.....


removing the can sensor and it fixes the problem indicates that you need to replace that sensor

Mar 28, 2017 | 1995 Nissan Maxima

2 Answers

Vibration when in gear, and stalling.


The problem is the torque converter solenoid. I had it happen on my 94 Cavalier a few years back and was a cheap fix at the local car mechanic. What happens is the transmission warms up and hits a certain speed where the solenoid engages, but then it sticks and won't disengage until it cools down sufficiently. When it sticks, it causes the car to shake when slowing down and will snub out the engine if you come to a stop.

Mar 09, 2009 | 1994 Chevrolet Cavalier

Not finding what you are looking for?
1995 Mazda Millenia Logo

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...