Question about Mitsubishi Diamante

1 Answer

Hi how do i adjust my handbrake on my mits diamante 1996

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Im assumimg its rear drum brakes ! Remove rear drums and inspect for shoe wear - if worn replace and have drums resurfaced ! If ok clean with brake clean making sure to keep your nose mouth and eyes covered to avoid getting brake dust inhaled or swallowed or in your eyes ! There is a adjuster knob on the shaft for shoe tension - some are asseable from a he through the backing plate and others you have to removemthe drum ! Adjust the whell in short increments and turn the the drum by hand until you can slightly feel or hear the shoe touch the drum mate surface - repeat for other sIde

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

There does not seem to have adjustment to lesson handbrake lever travel on 1996 mustang gt


Check underneath the carriage (under the car). Follow the brake linkage to the hand brake lever. You will probably find a mechanism that you can adjust for the handbrake level.

Mar 07, 2014 | Cars & Trucks

1 Answer

P0461 Trouble code on 2004 Mits Diamante


this code is for fuel tank level sensor, I don't think this is the reason for high emissions, can you give me the emissions results and I'll see if I can give you better advice?

Regards Jim

Jun 02, 2010 | 2004 Mitsubishi Diamante

1 Answer

I'm having issues putting the axle back int he transmission on my 2004 mitsubishi diamante LS


My expertise is with Mits Galants but most of that carries over to the Diamante. The front half shaft axles on the mits galant has a circle clip on the end that slides ionto the trans. I assume the Diamante have the same circle clip. Thes are suppose to be replaced each time you pull the axle but usually you don't have to unless they are bent or out of round. These circle clips are suppose to compress when you shove the axle in and then expand once the axle is in. Look at your axles and if the clips are messed up replace them (the clips not the axle). Ideally the axle just slides in with a good solid shove as long as you have the splines on the axle end aligned. There should be a minor catch from the circle clip as it is being compressed.

Feb 28, 2010 | 2004 Mitsubishi Diamante

1 Answer

How do i adjust 1996 excel handbrake


first thing to check is the rear shoe linings for wear. if they are to worn the handbrake would be very loose. this is where you adjust the brake. there is a shoe adjustment in the drum.

Jan 23, 2010 | Hyundai Excel Cars & Trucks

1 Answer

Need the code for rddio 97 diamante mits.


Each individual radio has a unique code, like every cars door has a unique key. If you lucky a previous owner may have put the code in the back of the owners manual. You may be able to get the code from dealer as well, although they will likely charge you a small fee.

Nov 26, 2009 | 1996 Mitsubishi Eclipse

1 Answer

How do get to and adjust handbrake cable on my 960 volvo


make sure e-brk shoe adjuster is all the way closed. then start adjusting little by little until you can slide disc back on and have a little friction when you spin it by hand, also hope your replacing dics, old one sometime have lots of rust stopping disc from going on anyway good luck and hope this helps.

Oct 20, 2009 | 1996 Volvo 960

1 Answer

I used handbrake to stop Disco when being towed to start vehicle. Right foot was on accelerator pedal left foot on clutch and without thinking applied handbrake. Result handbrake locked in off position....


You may need to get underneath and adjust the handbrake adjuster, but you could have done some damage to the transfer box/rear prop/diff as a result of your actions. Best to get it looked at by someone who knows what they're doing to assess any damage.

Sep 30, 2009 | 1996 Land Rover Discovery

1 Answer

How do you adjust the handbrake on a 1996 Peugeot 306 XR Hatchback ?


Handbrake is normally mechanically connected to
the brakes by steel cable 1/8 inch thick. At the end of the cables are bolts with adjusting nuts to adjust the handbrakes. These nuts must be adjusted to have an equal tension on the brakes, otherwise, swerving may result. It is advised to have a mechanic todo this job.

Sep 21, 2009 | 1984 Peugeot 604

1 Answer

Car handbrake adjustment


yes you need to check the handbrake ajustment first

Mar 14, 2009 | 2004 Volvo XC90

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...