Question about Ford F-250

1 Answer

I have a 98 Ford F250 with a 5.4 engine. I bought it, drove it around the block, realized it needed manifolds and a tune up but it still ran decent, so I pulled it in the shop and gave it manifolds and gaskets, and a set of plugs. Well when we tried to start it and pull it out of the shop it would barley haul it self. I put it on The computer and 2 codes came up (p0353 and p0357. I changed coil packs 3 and 7 and it make no difference? I'm stumped. It ran way better before we pulled it in the shop. lol

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 158 Answers

Regap the plugs or get the crossfire plugs

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car either has a cracked block, needs head gasket or? When I put water in the radiator, it comes out the oil pan without starting the engine.


I think a cracked block would be very unlikely. More than likely to be a head gasket problem. A decent mechanic shouldn't have any trouble pressure testing each cylinder to diagnose the fault. I'm assuming it's a V8? there are other possible causes also. Cracked head, faulty inlet manifold (v8, if it has water jackets in the manifold). I would have it checked out before assuming it needs a motor.

Nov 06, 2011 | 1997 Ford Mustang Cobra

1 Answer

Recently replaced the fuel pump and Battery. Seem to run really rough, like it's RPM's are high. I drove it about 10 miles, then turned it off , started it up and drove 10 miles back to my house and it ran...


a very common problem with those is that the intake manifold leaks and causes the car to take in more air than what it should resulting in high revs, take it to a garage and get it checked, it should be an easy fix and shouldn't cost alot either.

Dec 04, 2010 | 2000 Ford Focus

1 Answer

98- bonneville started to warm up ran for few minutes then died. waited about 1/2 then started again drove around block parked in drive let idle died again. also when it rains car idles rough .


check and or change the plug wires also check for a crack coil pack which is highly likely on that model and also check the ignition module as well

Jan 22, 2010 | 1998 Pontiac Bonneville

1 Answer

Sputters and dies while driving. Idles fine


probably a intake gasket or bad spark plug

Jun 18, 2009 | 1988 Ford F 150

1 Answer

Check Engine Light came on


get a scanner check code sound like vechicle speed sensor.

Apr 20, 2009 | 1998 GMC Jimmy

1 Answer

Oil plug came out didn't realize no oil pressure t


the oil is there to cool and lubricate the crank ( bottom end) and the cam shaft and valves (top end) the most likely out come is that you have (cooked) the engine, check to see if when you try to start dose the engine turn? if it dose then it could be the oil temp switch will need to be replaced. if the engine DOSENT turn then you have most probably welded the pistons to the block. seized the crank shaft or warped the head (head gasket) i hope this helps

Dec 01, 2008 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Wont run after engine swap


hello first thing check firewall ground to engine pass side if connected and good test ignition module if okay possible open signal on the spout connector check one other thing is the timing bypass chip near the distributor small plastic like a fuse size style usauly gray pull it out try to start with out it bypasses computors timing setting for manual adjustments goodluck

Sep 06, 2008 | 1998 Ford Taurus

2 Answers

Stalls / Dies / dead


this engine fuel pump prassurae low. it fuel pump celan. Your problem sovel

Jul 13, 2008 | 2003 Ford E150

3 Answers

Engin light


Out of the blue my light came on to. The code said was running to lean. I did a tune up. Found out it was well over due. New spark plugs and wires gave it much more power and runs smoother, they had been oxidized, fuel filter was needed also. Runs like new now. I did not realize my car was running so pore till i drove it after it had a tune up. Just a single mom's help hope it works.

Jun 19, 2008 | 2001 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...