Question about 1996 Toyota Tercel

1 Answer

Hi, Just got new motor mounts, lower control arms, front axle and calipers on my 1996 4-spd. Tercel. No engine or mechanical work was done whatsoever. She was running *perfectly fine* before work was done. When the mechanic dropped the car off, he showed me he'd cleaned the engine, which I didn't request. Now my poor baby bucks and hesitates when I accelerate, worse in higher gears than in 1st. Whay did they do to my TOY and how do I fix her? :( Thanks, Bruno

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 766 Answers

Probably water in the electrics, was it pressure washed or steam cleaned?. Check all electrical junctions, sockets and unions for signs of dampness - including spark plugs. Anything obviously wet, dry the best you can with a cloth and treat everything else with a hair dryer. As the engine gets warm it will tend to dry most everything out anyway.

Posted on Mar 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the lower front control arm on a 96 Nissan 200sx


put on jack stands, remove tire, remove brake caliper and bracket, detach outer tie rod end, remove axle bolt, remove hub bolts from strut, tape on axle with hammer to remove it from hub, loosen lower ball joint bolt, use fork tool to brake joint loose, remove hub and bearing, remove stabilizer links, remove bolts on lower control arm, replace every thing in reverse

Feb 01, 2015 | 1996 Nissan 200SX

1 Answer

I am trying to take the lower control arm on the passenger side of a 98 transport. The lower ball joint is being stubborn. I tried ball joint remover tool and not much room to work with and still dont


Lower Control Arm

Print
The lower control arm is a two-piece welded unit with a riveted ball joint. A conventional rubber bushing is used for the rear lower control arm pivot. The front lower control arm bushing is mounted vertically.


REMOVAL AND INSTALLATION

Some special tools are required to perform this operation including, a front hub spindle removal tool and a suitable ball joint separator tool.

WARNING Do not hammer or pry ball joint from knuckle. Failure to use recommended tools may cause damage to the ball joint and seal.
See Figure 1


0900c152801dbd3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Exploded view of the control arm-to-frame mounting

  1. Raise the vehicle and suitably support by the frame allowing the control arms to hang free.
  2. Remove the wheel and tire assembly.
  3. Remove the steering gear outer tie rod from the steering knuckle.
  4. Remove the stabilizer shaft link from the control arm.
  5. Remove the front drive axle shaft nut and washer.
  6. Use a suitable front hub spindle removal tool to Push the axle splines back out of the front wheel drive shaft bearing.
  7. Remove the drive axle from the transaxle.

Drive axle joint seal protectors should be used anytime service is performed on or near the drive axles. Failure to observe this could result in joint or seal failure.
  1. Place a modified inner drive joint seal protector on the drive axle joints.
  2. If equipped, remove the ABS wheel speed sensor jumper harness.
  3. Remove and discard the cotter pin, then loosen the nut from the ball stud.
  4. Remove the pinch bolt and the control arm mounting bolts, then remove the control arm from the vehicle.

Apr 20, 2013 | Pontiac Cars & Trucks

1 Answer

How to install rear struts on a 1999 llexus


selectachapter.gif

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

Print


Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

7923lgb6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:

    Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
  2. Adjust the parking brake.
  3. Stabilize the suspension as follows :
    1. Install the wheel(s).
    2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
    3. Raise the vehicle.
    4. Remove the wheel.
    5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.

  4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
  5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
  6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).

    Rear tire and wheel assembly

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Raise and safely support the vehicle.
  3. Remove or disconnect the following:
    NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.


    Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring

To install:
  1. Install or connect the following:

    Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel

  1. Before servicing the vehicle, refer to the Precautions section.
  2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
  3. Remove or disconnect the following:

    Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
  4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
  5. Remove or disconnect the following:

    Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
  6. Place matchmarks on the adjusting cam and body.
  7. Remove or disconnect the following:

    Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
  8. Secure the axle carrier in a vise.
  9. Remove or disconnect the following:

    Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal

    0996b43f802092da.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (inner)-LS 430

  10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
  11. Remove or disconnect the following:

    Axle hub

    0996b43f802092db.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub

    0996b43f802092dc.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle

    0996b43f802092dd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing


To install:
  1. Install or connect the following:

    New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.

    0996b43f802092de.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (outer)-LS 430
    Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.

    0996b43f802092e0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Installing the oil seal (inner)-LS 430
    New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable

  2. Lower the vehicle and turn ON the air suspension switch.



0996b43f80207fdc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear carrier assembly, hub and bearing-

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    WARNING Be careful not to damage the boot and ABS sensor


    Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier


    Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly

To install:
  1. Install or connect the following:

    4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
  2. Inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
  3. Press the hub out of the wheel bearing, then remove the backing plate.
  4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.
  1. Installation is the reverse of the removal procedure, while using the following torque values:

    Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)



0996b43f80208026.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor

To install:
  1. Install or connect the following:
    NOTE Inspect bearing back lash and hub deviation


    Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire


    Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
  2. inspect and adjust rear wheel alignment
  3. Check ABS speed sensor signal


Stabilizer Bar

Removal & Installation

  1. Remove the rear wheels.
  2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
  3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
  4. Remove the stabilizer bar.

To install:
  1. Install the stabilizer bar.
  2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
  3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
  4. Install the rear wheels.
  5. Inspect and adjust rear wheel alignment.


Strut & Coil Spring

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.


    No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
  3. Secure the strut in a vise.
  4. Compress the coil spring
  5. Remove or disconnect the following:

    Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

Dec 26, 2011 | 1999 Lexus ES 300

1 Answer

Need to replace 2003 corola front wheel bearings. need step by step instruction please


Removal & Installation To Remove:
toy_car_cor-02-04wheelhub1.gif

  1. Remove the front wheel.
  2. Remove the front axle hub nut.
  3. Disconnect the front stabilizer link from the strut.
  4. Disconnect the speed sensor (with ABS).
  5. Remove the front brake caliper and rotor.
  6. Disconnect the tie rod end.
  7. Remove mounting bolts and nut and separate the lower control arm from the ball joint.
  8. Using a plastic hammer separate the front axle shaft from the hub.
  9. Remove the 2 mounting bolts from the strut. Remove the knuckle and hub assembly.
  10. Remove the lower ball joint from the knuckle.
  11. Remove the axle hub snap ring from the knuckle. toy_car_cor-02-04wheelhub2.gif

  12. Remove the axle hub from the hub bearing using special tool 09520-00031 or equivalent hub puller.
  13. Remove the inner race from the axle hub using special tool 09950-40011 or equivalent puller.
  14. Remove the dust shield from the knuckle.
  15. Remove the axle hub bearing from the knuckle using special tool 09520-00031 or equivalent and a press.
To Install:
  1. Install the axle hub bearing on the knuckle using special tool 09950-600020 or equivalent and a press.
  2. Install the dust shield on the knuckle with 3 mounting bolts.
    • Tighten 73 in-lb (90 Nm).
  3. Install the axle hub on the knuckle using special tool 09950-600010 or equivalent and a press.
  4. Install the axle hub snap ring.
  5. Install the lower ball joint on the knuckle.
    • Tighten the ball stud castle nut 76 ft-lb (103 Nm).
  6. Install a new cotter pin.
  7. Install the knuckle on the strut with the 2 nuts and bolts.
    • Tighten 162 ft-lb (220 Nm) (except '03-'04) 113 ft-lb (153 Nm) ('03-'04).
  8. Lift the knuckle and hub assembly over the axle shaft and into the hub splines.
  9. Install the lower control arm on the lower ball joint.
  10. Connect the tie rod end to the knuckle.
  11. Connect the stabilizer link to the strut.
  12. Install the front rotor and brake caliper to the knuckle.
    • Tighten the 2 caliper bolts 79 ft-lb (107 Nm).
  13. Install the ABS sensor if equipped.
  14. Install the front axle hub lock nut.
    • Tighten 159 ft-lb (216 Nm) and stake the lock nut.
  15. Check the axle hub backlash and run-out.
  16. Install the front wheel.
  17. Check the front wheel alignment and adjust if necessary.
prev.gif next.gif

Feb 17, 2011 | Toyota Corolla Cars & Trucks

1 Answer

How do i remove front strut from 2003 ford tauras


Disconnect tie rod, end link and remove brake caliper. Disconnect ABS wiring. Remove lower control arm(ball joint) from spindle. Remove axle flange nut. Remove strut tower mounting nuts in engine compartment. Allow strut to slide down...Carefully remove axle from spindle, do not hammer the end. Use a center punch and hammer to remove it. Do not separate the axle components. There you go.

Feb 06, 2011 | 2003 Ford Taurus

1 Answer

Replace left front axle seal


First you'll have to remove the axle shaft, and here's detailed directions so use whatever info you need. First you'll need to jack up your vehicle place your jack just behind the front lower control arm mount. Take off your tire/wheel, remove the cotter pin and the axle nut retainer, remove the 2 caliper mounting bolts, move the caliper out of the way and support it so it doesn't just hang by the brake hose. Now, slide your rotor off, next you'll need to remove the axle nut and at 180ft lbs of torque you'll need a breaker bar or a heavy duty impact. The nut should be a 36mm if I remember correctly. Remove the bolts holding hub to steering knuckle, remove hub now you can tap it with a hammer to help loosen it from splines on axle shaft. take off the dust cover, pull the axle shaft out now, take out your bad oil seal, grease splines, then install new seal, carefully reinstall axle shaft to avoid damaging the seal, reverse steps and you're good to go. Good luck with your repair

Jan 29, 2011 | 1995 Jeep Grand Cherokee

2 Answers

What do i need to take apart to remove the drivers side front drive axel to replace the universal joint at the hub? could the axel slide threw the hole for the axel berring assembly or do you need to take...


Have not done this on your truck but book says just the upper ball joint needs separated. See procedure below from autozone.com. Please let me know if you have questions.
  1. Remove or disconnect the following:

    Front wheels (left side should be sufficient in your case) Front hub cotter pin, retainer and nut (axle nut)
  2. Using a floor hydraulic jack, support the lower suspension arm.

    Upper ball joint cotter pin and castle nut Knuckle from the front suspension upper arm
  3. Lower the lower suspension arm and steering knuckle slightly to facilitate easier halfshaft removal.
  4. Remove the 2 disc caliper mounting bolts, then lift the front disc caliper off of the front disc brake caliper anchor plate and position aside. Do not allow the caliper to hang by the brake hose; suspend it from the vehicle's frame with strong cord or wire.
  5. Remove the 6 front halfshaft-to-differential bolts.
    WARNING Use care to avoid damaging the hub seal when removing the front halfshaft.

    jturcotte_175.jpg

Fig. Halfshaft-to-differential mounting bolts (3 of the 6 bolts shown)-2001-03 F-150 and 2004 F-150 Heritage Edition


7. Remove the inboard end of the halfshaft from the differential case or extension axle case. Separate the front halfshaft and joints from the hub, then remove the halfshaft and joints from the vehicle.



To install:

  1. Slide the halfshaft outboard end into the hub, making sure that the splines engage.
  2. Situate the inboard end of the halfshaft against the front differential flange and install the 6 halfshaft-to-differential bolts. Tighten the halfshaft bolts to 60 ft. lbs. (82 Nm).
  3. Install the front disc brake caliper onto the rotor and anchor plate, then install and tighten the 2 caliper mounting bolts to 21-26 ft. lbs. (28-36 Nm).
  4. Lift the lower suspension arm and steering knuckle up until the upper ball joint stud is inserted into the steering knuckle. Install the upper ball joint castle nut and tighten to 57-76 ft. lbs. (77-104 Nm). Install a new cotter pin.
  5. Install the hub nut onto the halfshaft and tighten the hub nut to 221 ft. lbs. (300 Nm).
  6. Install the hub nut retainer and a new cotter pin.
  7. Install the front wheels and tighten the lug nuts in a star-shaped sequence to 83-112 ft. lbs. (113-153 Nm).
  8. Lower the vehicle to the ground.

Jan 23, 2011 | 2002 Ford F250 Super Duty SuperCab

1 Answer

How do i change out my rear end


remove wheels calipers and rotors, remove rear cover and drain oil from diff, remove abs sensors if it has abs,remove axle shafts, this is done by removing the 8mm bolt holding the pin, slide pin out push axle in to remove c clip holding axle then slide out, do the same to other side, note dont spin diff or gears will fall out,dissconect driveshaft, next remove axle vent and unbolt brake hose from axle,leaving brake lines connected unclip them from axle housing, next support diff with jack, dissconect lower shock bolts and slide shocks to side, remove upper control arm bolts from diff, slowly lower diff to release spring tension now remove springs and remove lower arm bolts. lower diff and take out. reverse to install. hope this helps.

Aug 27, 2010 | 1996 Ford Crown Victoria

1 Answer

How do I replace my front passenger wheel bearing?


first remove the wheel,then remove brake caliper by removing two mounting bolts,then remove the caliper mounting bracket two more bolts 15 mm socket,now remove the axle nut 30 mm socket,before removing axle the lower ball joint has to be dislocated and lifted out of lower control arm.tie rod also has to be dislocated to make job easier,now push axle out of wheel bearing then remove the three bolts that hold it in,in most cases you have to beat a chisel in between the bearing and its housing reverse installation.

Jan 17, 2010 | 2002 Ford Taurus

1 Answer

How to put on right front cv axle and both lower ball joints and idler arm.


Bring it to your mechanic this is not easy you need to take the wheel off
unbolt the axle if you can get the axle out without taking off the ball joints than do so but usually you will need a big set of tools and special puller for the idler arm. Make sure you disconnect the abs sensor or wire going to your brakes take center bolt out of center of rotor take ball joint nuts off.You need a ball joint seperater.Only use on junk ball joints.
Pull rotor assembly and caliper braket and rotor off in one peice be carefull not to break the brake lines to the caliper.If you are going to attempt this it can lead to serious bodily injury it should be done by a mechanic.After this is done unbolt cv axle from axle transfer case/transmition.The ball joints need a press and may need to be heated to get out of control arm.Bring it to a mechanic or met a nice guy that will do it cheep

Jan 15, 2010 | 1993 Isuzu Rodeo

Not finding what you are looking for?
1996 Toyota Tercel Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...