Question about Ford Thunderbird

1 Answer

No flluid going to back brakes - Thunderbird Ford Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

You might need to replace the master cylinder.

Posted on Mar 14, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Carburetor vacuum diagram


The flexible brake hoses that screw into the calipers are the most neglected part of most brake systems, along with dirty flluid. The flex hoses are probably swollen inside and holding pressure on the calipers. Remove the flex brake hoses and try to blow through them. If you cannot or it is very difficult the hoses are bad.At a minimum I recommend replacing hoses on both sides. As for stuck pistons, try collapsing the calipers. If the pistons won't retract then replace the calipers too.

Mar 14, 2014 | Cars & Trucks

1 Answer

Recently had brakes redone now i have heat on rotar and the brakes seem to be engaged how do i correct the problem


Check for propper brake fluid on system, somtimes human error can put power steering fluid intead of brake flluid. If this has ocurr, you must bleed all the brakes system. Sammyc47

Feb 21, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

How to replace thermostat


flow the hose from your ratater to your water pump undo 2 bolts clean and remove the old gasket replace with now one put new thermostat in rebolt not to tight that you will crake it and check flluids and make sure it not leaking ...

Jan 22, 2011 | 2002 Buick Century

1 Answer

Can i use prestone synthetic dot4 brake flluid in my 2000 mazda 626?


Yes you can do that and it will help a lot but before you do that is best if you remove all the old fluid from the vehicle inclusing the oil in the lines

Nov 21, 2010 | 2000 Mazda 626

1 Answer

Brake pedal is really low and i changed brakes and bleed them. ? Got no oil coming out back right tire though?. Could it be my master cylinder or my transfer box??


Do you have fluid coming out of your front left brake? This is the other half of the circuit.I think you need to open up the bleeder screw and have a friend depress the brake pedal to the floor slowly and hold it down.Tighten bleeder ,release brake,repeat this till you get fluid.If you don't get flluid after several attempts (6-8).Then it might be the metering and proportioning valve in the master brake cylinder is done and you are going to have to replace the unit.Unless you changed a line ,caliper or wheel cylinder there should be no air in the system. Also check for crushed or pinched brake lines.Good Luck

Nov 16, 2010 | 1997 Dodge Caravan

1 Answer

How do you change the 4x4 flluid on a 99 silverado


You should have two plugs on the back of the unit (in most cases)
One is higher than the other.(usually they are about 1" in size) High one is fill...remove that one first (if you can't remove it then you can't refill it, so don't remove the lower one) Once fill is free, remove the drain, wait till fluid stops running then replace drain plug and fill till fluid just seeps from the lower edge of the hole (on level ground) Replace the fill nut and you are done!

May 14, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Cant locate where to put power steering fluid into a 97 riviera


The power steering pump(with reservoir attached) is on the passenger side of engine on the bottom left side under the alternator.

Jan 18, 2009 | 1997 Buick Riviera

1 Answer

1996 Ford Taurus transmission "dumps " fuild


There are no guarantees when it comes to a rebuilt transmission or anything. They usually have a warranty for the work all depending on the mileage afterwards. Is it over it? Most likely the gaskets need replacing and the bolts tightened again.

Sep 13, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...