Question about 1996 Ford Taurus

Open Question

WHERE IS THE CANISTER PURGE SOLENOID LOCATED ON A FORD TAURUS 1996 GL

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 169 Answers

SOURCE: '96 Regal Purge Canister Valve?

ADAM
THE PURGE SOLANOID IS ON THE ENGINE WITH A RED CONNECTOR ON IT. IT IS LOCATED ON THE REAR OF THE ENGINE ABOVE THE REAR VALVECOVER. YOU ARE ACTUALLY LOOKING FOR THE CANISTER VENT SOLANOID AND IT IS IN THE REAR OF THE CAR AND THEY FAIL OFTEN. GET THE PART FROM G.M. AND THEY CAN TELL YOU EXACTLY WHERE IT IS. THE G.M. PART IS UNDER $30.00.

Posted on Aug 26, 2008

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 9 Answers

SOURCE: where would the carbon canister

next to the air filter

Posted on Apr 17, 2009

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

co7196
  • 3433 Answers

SOURCE: Engine Light On: '06 Ford Taurus

ck in engine compartment. breside the radiato, more like the right side facing the car.. It kooks like a plastic canister wiyh two or three hosrs on top. sensor should be theref very close by

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Purge valve solenoid canister located on a 2003 Ford Taurus code po457


  • Park the Taurus on a level surface, set the parking brake and turn off the engine. Chock the wheels.
  • Open the hood and disconnect the negative battery cable.
  • Stand on the passenger's side and shine the flashlight along the firewall.
  • Look for a plastic cylindrical object about 2 inches high, mounted on the firewall near the right fender. This is the purge valve. You should see a thick black hose entering it from the driver's side of the unit.
  • The Ford Taurus canister purge control valve is a part of the evaporative emission control system, which keeps fuel vapors from escaping into the atmosphere. Pressure inside the gas tank fluctuate due to fuel level, environmental conditions and driving style. The extra vapor is vented into a storage canister under the rear of the car, outside the fuel tank, and is fed into the purge control valve through a rubber hose. The power-train control module monitors fuel tank pressure through a tank pressure sensor. It opens the canister purge valve as necessary to keep this pressure within design limits.

Feb 18, 2017 | Ford Taurus Cars & Trucks

1 Answer

Trying to locate canister purge valve solenoid on vehicle


There is a canister purge valve & a volume control purge valve on your truck. The canister purge valve is on the evap. canister itself(at the rear of veh. near the fuel tank. The volume control purge valve is located in the eng. compartment, passenger side behind Battery. You didn't mention if it's a 4 or 6 cyl.

Aug 10, 2014 | 1996 Nissan Pickup

1 Answer

1995 ford taurus vacuum solenoid located


Another case of the the person asking the question not giving enough information. What engine does your Taurus have? There are several different vacuum solenoids on this car.
If you are referring to the Canister purge solenoid [emissions system], it is located in the vacuum hose going from the Carcoal cannister, to the engine. It will have 2 vacuum hoses & 2 electrical wires [in 1 plug] attached to it.

Oct 05, 2011 | 1995 Ford Taurus

1 Answer

Ive got a 96 ford taurus gl that im working on. they put gas in drove it home and now it wont start. i looked under it and could see fuel leaking out of the vapor canister whenever tried to start. could a...


Hello! The vapor canister is more than likely plugged...The carbon granules can infiltrate the entire fuel system...I would suggest #1...Replace canister...and fuel filter..#2....Relieve fuel pressure, disconnect battery, remove and clean the fuel rail and injectors...On 8/12/1996 there was a recall on your vehicle addressing the fuel and injection system...If the recall was performed there should be a sticker on the inside of the drivers door...The original culprit is the Fuel Vapor control Valve which is allowing fuel to enter the vapor lines...see diagram below...


saailer_163.jpg

saailer_164.jpg

Fuel Vapor Purge Valve:

MOTORCRAFT Part # CX1687 Cost $80

Guru.................Saailer

Aug 28, 2011 | 1996 Ford Taurus

1 Answer

On a 96 impala, where is the purge solenoid located?


Look on the underhood sticker. Locate the emissions canister (or charcoal canister). The skinny line coming from it is the vacuum line. Follow it, and it should lead you to the canister purge solenoid.

Aug 26, 2011 | 1996 Chevrolet Impala SS

2 Answers

Diagnostic code for 96 ford ranger-code number - p1443


Check the voltage on the purge flow (PF) sencor, with engine running...

Jun 19, 2011 | Ford Ranger Cars & Trucks

1 Answer

I need to repace a solenoid/small or no purge flow condition for a 1996 ford escort lx1.9 motor.Ineed it for emmision testing.Where is the part located on top where the motor is or in the where the...


The valve/solenoid is next to the battery--see picture below. here is the procedure from autozone.com. Let me know if you have questions.

Evaporative Emission (EVAP) Canister Purge Valve
  1. Disconnect the negative battery cable.
  2. Unplug the canister purge valve electrical connection.
  3. Tag and disconnect the vacuum lines from the valve.
  4. Remove the valve from the car.
To install:
  1. Install the valve and connect the vacuum hose.
  2. Attach the valve electrical connection.
  3. Connect the negative battery cable.

d5d7dc5.gif

Oct 15, 2010 | 1996 Ford Escort 4 Door

1 Answer

How to fix obd2 code 1443 on 96 ford ranger emisson test failed


It is usually carbon pieces from the evap carbon canister clogging the purge solenoid and purge flow sensor. There should still be a one piece purge solenoid and purge sensor with hose assembly available. You will also need to replace the carbon storage canister.
After replacement disconnect the negative battery cable, hold your foot on the brake pedal for 30 seconds, then reconnect the battery.

Oct 25, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Engine Light On: '06 Ford Taurus


ck in engine compartment. breside the radiato, more like the right side facing the car.. It kooks like a plastic canister wiyh two or three hosrs on top. sensor should be theref very close by

Jun 11, 2009 | 2006 Ford Taurus

Not finding what you are looking for?
1996 Ford Taurus Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...