Question about 2001 Chevrolet Prizm

1 Answer

Shift linkage clips are rusted,and i cant find the bolts. right side axle nut is not budging

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Sdfsdfdssf

Posted on Mar 13, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

Can't get my 92 f-150 flare side 4x4 shift lever to shift in to 4wd I've yanked and yanked on it to no avail seems to be stuck in 2wd and won't budge. ( go into 4wd)


If you have to push your shifter to one side or the other to pull back, the mechanism is frozen, rusted. If its a straight pull back, you will need to remove the pivot bolt (1") and remove the shifter assy. The pivot bolt retains 2 plastic/nylon bushings. You will need to get this bolt out of the shifter without heating it. When you get the bolt out, you will need to wire wheel the shank on the bolt, to remove the rust and corrosion. When installing the bolt and bushings back into the shifter, use anti seize on the shank of the bolt, and install it.

Nov 03, 2013 | Cars & Trucks

2 Answers

How remove the rotor to change bearing for 2005 chev colorado front


first you remove all the lug nuts and the wheel and tire. To get the rotor off you will need to remove the brake caliper. they are held in with 1/4" hex screws. If you don't have an allen wrench you can use a socket extension to removes these. Once unscrewed the calpet simply lifts off the rotor and the rotor is ready to come off. You will need to remove the axle nut and keeper then the rotor slides off towards you and the wheel bearings will come out with the rotor.

Sep 26, 2011 | 2005 Chevrolet Colorado

1 Answer

How do u take off the oil pan on a 1999 awd bravada 4.3


Hello skullz, this is a fairly big task but it can be done in your driveway. Take your time, keep track of all your parts you remove. Use masking tape and a sharpie to label stuff if you feel like it will make easier to reinstall....These steps are for a 99 blazer 4x4 with an aluminum pan. You wont need to do some of the shift linkage removal due to the AWD and electronics the Olds has.

Disconnect battery and remove battery tray. Disconnect shift cable at actuator. Raise and support vehicle.

Remove underbody shield from steering linkage and engine oil pan. Drain crankcase. Remove starter motor.

Remove oil cooler pipes and both front wheels. Disconnect electrical connector and remove wiring harness bracket at shift cable housing.

Remove 3 shift cable housing bolts and disconnect shift cable from differential carrier. Remove both front drive axles. Remove differential housing.

Remove 10 oil pan bolts, 2 nuts at crankshaft rear oil seal and remove 2 transmission to oil pan bolts....Remove oil pan from vehicle....When you reinstall & tighten the oil pan bolts, start in the middle of the pan and go back to the bellhousing, directly across from each bolt---left, right, left right...then, from the middle towards the front of engine, right, left, right left...Torque to 18 ft/lbs

Good luck... if you tackle this job its a fun one....

Jul 14, 2011 | Oldsmobile Bravada Cars & Trucks

2 Answers

Is the back up switch connected to the shifting linkage of the automatic transmission on my 1988 ford bronco II


If you have the C5 trans, here is the info:

C5 Transmission
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the downshift linkage rod from the transmission downshift lever.
  4. Apply rust penetrant to the outer lever attaching nut to prevent breaking the inner lever shaft. Remove the transmission downshift outer lever attaching nut and lever.
  5. Remove the two neutral start switch retaining bolts.
  6. Disconnect the multiple wire connector.
  7. Remove the neutral start switch from the transmission.

To install:

  1. Install the neutral start switch on the transmission. Install the two retaining bolts.
  2. Adjust the neutral safety switch following the above procedure.
  3. Install the outer downshift lever and retaining nut, and tighten the nut. Install the downshift linkage rod with the retaining clips.
  4. Connect the wire multiple connector. Check the operation of the switch. The engine should start only with the transmission selector lever in N or P.

If it is the:
C3 And A4ld Transmissions
It's on the transmission....


// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 35; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> c17hydro_179.gif

Neutral start switch and its location on the C3 and A4LD transmissions

May 12, 2011 | 1988 Ford Bronco II

1 Answer

Right axel outer universal joint needs to be replaced? How do you replace it.



Removal & Installation


See Figure 1

  1. Raise and support the vehicle safely.



CAUTION Brake linings may contain asbestos. Asbestos is a known cancer-causing agent. When working on brakes, remember that the dust which accumulates on the brake parts and/or in the drum may contain asbestos. Always wear a protective face covering, such as a painter's mask, when working on the brakes. NEVER blow the dust from the brakes or drum! There are solvents made for the purpose of cleaning brake parts. Use them!

  1. Remove the wheels and brake assemblies.

Refer to Brakes for the proper procedures concerning brake removal.
  1. Remove the cotter pin, locknut and axle hub nut.
  2. Remove the hub-to-knuckle attaching bolts.
  3. Remove the hub and splash shield from the steering knuckle.
  4. Remove the left axle shaft from the housing.

  1. If equipped with Command-Trac, disconnect the vacuum harness from the shift motor and remove the shift motor from the housing.

Remove the right axle shaft from the housing.


remove c clips from u joint remove caps install new u joint install clips

To install:

  1. Insert the left and right axle shafts into the axle tube.
  2. To install the right axle shaft (with Command-Trac) first be sure that the shift collar is in position on the intermediate shaft and that the axle shaft is fully engaged in the intermediate shaft end.
  3. If equipped with Command-Trac, install the shift motor, making sure that the fork engages with the collar. Tighten the bolts to 8 ft. lbs. (11 Nm).
  4. On the left side, install the axle shaft in the housing.
  5. Partially fill the hub cavity of the knuckle with chassis lube and install the hub and splash shield.
  6. Tighten the hub bolts to 75 ft. lbs. (102 Nm).
  7. Install the hub washer and nut. Tighten the nut to 175 ft. lbs. (237 Nm). Install the locknut. Install a new cotter pin.
  8. Install the brake assemblies.
  9. Lower the vehicle.

Sep 13, 2010 | 1996 Jeep Grand Cherokee

3 Answers

2005 equinox wheel bearing assy wont come out


okay i assume the rotor is off,remove the bolts out the back, take a hammer and beat the front of the hub the top then bottom then the sides to free,hit so that hub pull out,you will be hitting the back side the hub where the wheel would sit,if that doesnt work then use a chisel to break free, stick it where the hub meet spindle,ITs just frozen beat it.a56579d.jpg

May 15, 2010 | 2005 Chevrolet Equinox

2 Answers

Having trouble removing axle nuts from my 2000 Villager


if replacing the shaft heat the nut up for it sounds like its rusted solid.... the heat will break down the hold from the rust

May 12, 2010 | 2000 Mercury Villager

3 Answers

How to replace front cv shafts on a 1997 isuzu rodeo ?


Remove tire, remove axle nut, pop ball joint off, remove clip, pull axle

For a more detailed instructions, go to autozone.com and register for free.
Now you will have full free online repair manual

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
2001 Chevrolet Prizm Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...