Question about 1984 Chevrolet S-10

1 Answer

Won't start/replaced battery/ 1984 s-10 chevy pickup

Posted by on

1 Answer

You tested the starter?

Posted on Mar 13, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1997 Chevy C1500 pickup won't start?


You need to have the ignition control module checked (It's inside the distributor)

Apr 21, 2013 | 1997 Chevrolet C1500

1 Answer

How to replace gmc1990 pickup coil


I assume this is the HEI coil. If not let me know and I can help further.
Instructions
    • 1 Put your safety first. Engage your emergency or parking brake. Also, disconnect the negative battery cable from the Chevy Corvette's battery.
    • 2 Make the ignition system visible. On older models, you may need to remove the plenum extension for the intake manifold using a screwdriver or wrench. For newer models, remove the cover for the fuel rail.
    • 3 Look for additional parts that you need to remove. For HEI systems, you need to access the distributor through the cap. Other systems use an ignition coil harness connector.
    • 4 Disconnect the secondary wires, or spark plug wires, from the ignition coil. Tag each wire with masking tape, so you know which terminal to reconnect the wire to. If you connect the wrong wires to the terminals, your Chevy Corvette won't start.
    • 5 Detach the ignition coil mounting bolts and remove the ignition coil. The amount and type of bolts vary depending on the part number for the Corvette ignition coil. You may also need to remove the ignition coil arc seal.
    • 6 Clean the distributor cap with a soft cloth. Now is a good time to replace the seal, if needed. Insert your new ignition coil and secure it in place. As you reassemble, use a Torque wrench to tighten the mounting bolts or screws to 13 inch pounds (1.5 Nm) of torque.
    • 7 Reassemble the rest of the parts and reconnect your battery. Start the Chevy Corvette to ensure the repair worked.

Oct 18, 2012 | 1990 GMC Sierra

1 Answer

Changed alternator, cranks but won't stay cranked


your gonna need to plug a scanner in and check the ECM for trouble codes before going any further

Aug 18, 2012 | Cars & Trucks

1 Answer

1995 s-10 chevy pickup no brake lights won't work


Check your fuses, if all ok then the switch on your brake pedal is at fault, Look at the top of the brake pedal and you will see the location of the switch.

Mar 10, 2012 | Cars & Trucks

1 Answer

I have a 1996 chevy pickup that won't start. Fuel


Have you sprayed fuel/starting fluid into the engine to see if it starts? You can have fuel pressure but no injector fuel delivery, we call this "pulse"

Feb 07, 2012 | 1996 Chevrolet K1500

1 Answer

My !978 chevy pickup has new distributor and carburator. I can hear it firng but it won't start


gyver here , twenty year wrencher.. sounds like either you got the timing out on the distributor , or the timing on the crank and cam are off. if you know the timing marks were set cam at twelve crank at six the dist is out. common for guys to set cam and crank n marks one above the other but then you must rotate engine 360 degree before you set dist back into hole. pull dist up rotate 180 degree .let me know

Feb 01, 2012 | 1978 Chevrolet C1500

1 Answer

1999 z71 1500 chevy pickup won't start


Has the check engine light come on at all ?

Jan 26, 2012 | 1999 Chevrolet Silverado 1500

2 Answers

Need to replace serpentine belt


Serpentine Belts are relatively easy to replace with just a wrench. Locate the tensioner (spring loaded) and when you move it CW it will loosen the belt. There should be a diagram of the belt routing on the frame close to the battery, if not it will also be in your owners manual.

Aug 01, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire


sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

3 Answers

1998 chevy malibu


have you checked for corrosion on the battery cables or tryed to jump it or had the battery tested

Mar 28, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...