Question about 2007 Chevrolet Uplander LT Minivan

Open Question

2007 chevy uplander. Loose feeling in the front end, pulls to the right yet has a sway to it also. Just replaced the brakes and rotars. There is a clunk in the front end when excelerating quickly or braking quick. Just feels like a lag inbetween till the van catches up then clunks. Overall front end doesn't feel tight. Please help if possible.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2003 Dodge Caravan Front end clunk.

Had similar problem with 2003 Dodge GC. Replaced the parts you mention + rack & pinion, then to fix the now noticable whining noise, replaced power steering pump and pulley. Fortunately was under an extended warrentee at 46k miles.

Posted on Jul 19, 2008

BigBlue77
  • 59 Answers

SOURCE: 2004 clunking noise thru steering!

Its probably the intermediate steering shaft. The shaft where it goes thru the firewall is known for clunking on these trucks. GM makes a lube kit to fix the noise. I don't have the part number handy, but the parts guy at the local dealer will know what you are looking for.

Good Luck

Posted on Sep 20, 2008

  • 3 Answers

SOURCE: 2002 caravan clunking problem

may be boll joint
or sway bar link .

Posted on Jan 22, 2009

  • 49 Answers

SOURCE: 2002 clunking problm

Check the macpherson struts to ensure they are not loose.  One way to check is visually in the engine compartment.  Check the top of the struts to ensure the nuts are not loose.  Another is to raise the side of the van where you hear the clunk.  Raise it so the wheel is off the ground.  Grasp and shake the strut to see if it is loose.  The struts should not be loose, but you never know.  As the strut is certainly ivnolved in bumps and rotates when the wheel turns, I would check there since you have already explored the bushings and links.

Posted on Jan 24, 2009

  • 29 Answers

SOURCE: 2000 Explorer Clunks, sounds "loose" suspension

it sounds like the radis arm bushing are wore out they are the arms that go between the frt. axle to the frame they have round bushings that are bolted the the frame rails just behind the frt tires.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 uplander and it vibrates like the steering wheel shakes left and right when driving down the highway if I take my hand off the steering wheel it drifts to the right but when I take my foot...


start with tires; rotate them front to back

then check suspension components; anything loose will cause shimmy of any kind

brake rotors can be warped as well

Mar 30, 2015 | 2007 Chevrolet Uplander

1 Answer

1998 Chevy Blazer LS...Replaced driver side sway


need too have the front end lined up and probly need too replace the tie rod ends

Sep 21, 2014 | 1998 Chevrolet Blazer

1 Answer

Chevy uplander traction control seems to be working all the time


Can you feel the vibration through the steering wheel if so have your front discs machined & the front pads replaced. Or are you feeling the vibration through the pedal? if so it may be the rear but start with the front.

Jul 15, 2012 | 2005 Chevrolet Uplander

1 Answer

How can I change the front signal lamp on the Chevy uplands 2007?


The headlamp assembly must be removed. There is a pin and small bolt that need to be removed then the head lamp can be pulled out. This will give you access to reach down and twist the signal lamp socket loose.

Jul 25, 2010 | 2007 Chevrolet Uplander

1 Answer

Should the brake rotor be loose when you take the wheel off? I have been experiencing popping noises from the front end going over bumps as well as putting on the brakes. Just pulled the right front tire...


The wheel holds it on tight. What you see is how it is. The rotor shouldn't have much of a step or ridge on the outer edge. You can remove the rotor and file or sand it off or have them turned at the auto parts store. Then sand off all rust on pad sliding surfaces and put anti-seize on those areas. That eliminates the front brakes. Check out sway bar bushings and end links, if applicable.

Mar 11, 2010 | 2002 Chrysler Sebring

2 Answers

I have a 1994 Chevy k 1500 and it has a clunk in the driver side right about infront of the door. now i have had all the tie rod ends replaced and the ball joints have been checked and are fine. it only...


Sounds to me like you need a set of sway bar links replaced.It also may be the sway bar bushingsYou may want to check the front brakes as well,you could have a slider bolt missing.

Dec 16, 2009 | 1996 Chevrolet K1500

1 Answer

2004 dodge qc 4x4 with front end rattle on drivers side. I jus replaced brakes and rotars Oct 08.


Sounds like a bottom ball joint. Jack the car up, take hold of the top and bottom of the tyre and push and pull it hard. This should conform it with a loose movement and the rattle you can hear

Aug 11, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
2007 Chevrolet Uplander LT Minivan Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...