Question about 2008 Nissan Titan

Open Question

2008 nissan titan with a crank but no star hook up my scanner and scanner would nat communicate with ecu

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: 02 outback 3.0 h6

try you map sensor or your throtle pos sens. your fuel pump is designed to run all the time. it is suppose to run through the fuel rail and back to the tank in a constant cycle.

Posted on Jul 04, 2008

  • 67 Answers

SOURCE: 2001 sentra no communication with scan tool

Take a few minutes to make sure you dont have a blown fuse....Run through them with your test light...

Posted on Feb 11, 2010

emissionwiz
  • 75066 Answers

SOURCE: Replacing the mirror lens only

is this just the glass element?, or the glass and the plastic backing that pops into the mirror?

Posted on Oct 11, 2010

ZJLimited
  • 17970 Answers

SOURCE: Replacing the mirror lens only

Remove the triangular cover lining.
A) Disengage the wiring connection and insert the male end of the connector back inside door frame so it can easily be removed.
B) Caution: Be careful not to drop the mirror housing. Secure the mirror housing with one hand, remove the (3) nuts holding the mirror housing to the door frame using a 10mm socket.

Carefully remove mirror housing from door frame and set mirror housing on a cloth covered surface.

C) Push down on the upper inboard edge of glass until mirror pivots fully outward. Insert a large slotted screwdriver in between the slotted hole. Carefully pry and twist screwdriver until original mirror pops off. If heated, disconnect heater wires from heater terminals and remove mirror.

Hope helps.

Posted on Oct 13, 2010

  • 1 Answer

SOURCE: 2001 sentra no communication with scan tool

2001 nissan sentra gxe ecu not communicating, tried the fuse, fuse keeps blowing.

Posted on Jun 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Nissan titan cc SE 5.6L 4wd just programmed new ecu now need to know the throttle relearn procedure with a consult 2 my name is Michael Toovak from Barrow ak.


Don't know with the scan tool but this may help:

http://www.titantalk.com/forums/titan-faq-how-area/25118-how-ecu-reset-throttle-accelerator-position-learning.html

Jan 19, 2016 | Nissan Cars & Trucks

1 Answer

2008 titan cranks no start no communication with modules pops off every once and awhile usually when battery voltage drops


Battery Dead ?

Why does the battery voltage drop & why
are you not working on that issue ?

What has been tested so far & how & results ?

Nov 14, 2014 | 2008 Nissan Titan

1 Answer

2008 Nissan titan cranks but no start no cumin ovation with ECM check fuses and fusible links all checked out good fuel pump is good but doesn't come on


Nissan had a problem with the circuit board in the main fuse block getting a crack in it and creating the no start condition. IDPM is the name that Nissan calls the part.

Nov 07, 2014 | 2008 Nissan Titan

1 Answer

Timing chain diagram for nissan titan 2008 5.6 ?


If you are taking on such a huge job as a head gasket on a Titan, why oh why didn't you MARK EVERYTHING.

Sep 14, 2014 | 2008 Nissan Titan

2 Answers

Titan turns over but does not start


Titans have had an issue with a relay in the IPDM(fuse block), when I was at Nissan we replaced about 3-4 a week for the same problem.

Feb 03, 2013 | 2008 Nissan Titan

2 Answers

"service engine soon" light is on


It needs to be scanned by a code reader or scanner to realy find out the problem.

Jan 10, 2011 | 2008 Nissan Titan

2 Answers

Trouble code u1000 on nissan titan


DTC (Diagnostic Trouble Code) U1000 is a problem with the CAN communication line.
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each control unit shares information and links with other control units during operation

This DTC sets under the following conditions:

The ECM (Engine Control Module) has lost communications with one or more of the onboard control units for a specified amount of time.

To diagnose this code you must scan all the other modules to see if they can communicate with the scanner. If all the modules are able to communicate with the scanner then the problem is intermittent and can be very hard to find. If you have one or more modules that fail to communicate then the problem is the data line to that (those) module(s).

Dec 19, 2010 | 2005 Nissan Titan

1 Answer

I have a 2008 nissan Titan. I have the Delphi harnass hooked up but when I plug in the harnass to the trailer I have running lights only. No brakes or turn signals. Do I need to do something with the blue...


Check for the tow relays in the under hood fuse box. Black box behind the battery on the passenger side. Do a web search for 'titan tow relay' for more info.

Mar 20, 2010 | 2008 Nissan Titan

Not finding what you are looking for?
2008 Nissan Titan Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...