Question about Lincoln Town Car

1 Answer

TRYING TO INSTALL A PULLEY BELT IN A 91 LINC - Town Car Lincoln Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers


Posted on Mar 13, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No Space between the Belt at the Idler Pulley and the Water Pump Pulley. On a 4cyl without Air conditioning

check and make sure of the proper routing of the belt. If good check the idler tension spring, check the bearings in all the pulleys the belt runs over.

Apr 04, 2013 | Cars & Trucks

2 Answers

2000 Mercedes e320 with a frozen a/c compressor what size belt do I need to bypass?

There is no belt to do this, you must install a compressor bypass pulley also known as an "AC Delete" pulley. All cars come with the same belt with or without AC. Contact the dealer on this, but not sure they can help as AC is standard on US models unless you order it deleted, which of course no one does because of the wait time to have the car shipped from Europe due to the special order.

Jul 19, 2012 | 2000 Mercedes-Benz E-Class

1 Answer

How do i change serpentine belt ply voy

There are two pulleys that have no ribs on most Voyager engines from at least 91 thru 2003. One, the idler pulley is stationary. The other, The tensioner pulley is mounted to a spring loaded arm and in intended to keep the belt properly tightened. The tensioner pulley is attached to its arm with a 15 mm bolt. The tensioner assembly is rotated toward the front of the vehicle by putting a 15 mm box end wrench on that bolt and turning it clockwise as if you were trying to tighten the bolt. The belt will loosen which will allow the belt to be removed. There is, or should be a belt routing guide mounted under the hood. Use that guide to install the new belt. Here's the trick. With the belt installed on all of the pulleys except the tensioner, position the belt against the pulley as if to slide it on, THEN put the wrench on its bolt, pull forward until the belt slip over the pulley and then let the tensioner rotate counter clockwise until the belt is tight. BE CAREFUL: the grooves in the belt must be in the correct grooves in the pulleys that have grooves. Check them twice from the top and the bottom. Good luck!

Apr 29, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

Im trying to get the timing marks aligned and dont know where to align them to. Its my neighbors car and he doesnt have a service manual. Someone else tried replacing the timing belt for him and didnt...

with the timing belt on the vehicle install the botton piece of the timing cover with crank pulley. line up the notch on the crank pulley with 0 on the timing cover for top dead center on the crank. then there is a small sight hole in the spokes on the camshaft timing gear. with the belt off the timing gear line up that sight hole with a notch behind the gear on the cylinder head. you will only be able to see the notch through the sight hole with a mirror. once these are lined up slide the belt back on the timing gear and recheck afterward. this the procedure for all 5s-fe motors

Nov 12, 2009 | 1991 Toyota Celica

1 Answer

Leak from the water pump

  • first of all you are probably going to need a torque wrench for the crank shaft pulley bolt it has 225lbs.of torque or more.I just did one on my 1991 honda accord dx .you have to take off a/c belt ,alternator etc. on the crank pulley.(I took it to a shop and they heated the 3/4 in. bolt and used torque wrench. I broke a half inch breaker bar trying to get it offf) next use puller to take off crankshaft motor and remove motor mount bracket. take off upper and lower timing belt covers.take off timing belt and other belt using the tensioners.take off and replace water pump CHECK ALL TIMING MARKS with #1 piston@TDC. There are about 6.

Jun 02, 2009 | 1991 Honda Accord

1 Answer

Trying to install a new belt on a k1500 truck

the idler pulley is located front center just lower than engine blocks top..usually a diagram is located on radiator/fan shroud.....relieve tension to belt by torquing idler pulley away from belt and remove/replace with nwe belt then add tension and slide belt over b4 releasing pulley

Jan 13, 2009 | 1995 Chevrolet C1500

1 Answer


remove your alt and take it into the auto parts store they can check it for you

Sep 03, 2008 | 1991 Lincoln Town Car

1 Answer

Crankshaft pulley Nissan Pulsar '91 N14

Hi your alternator pulley is hold by a nut about twenty mm, chech it it may be lose......good luck

Aug 24, 2008 | 1990 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

79865 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides