Question about Ford Mustang

1 Answer

1989 mustang i'm trying to fix a leaky rack and pinion and i can't seperate the inner tie rod from the rack assembly. my manual says there is a spiral pin holding it on. what is a spiral pin? and how do you remove it?

Posted by on

1 Answer

You have to replace the rack

Not repairable,only by the
rebuilders

Posted on Mar 13, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change power steering pump


Play in the steering wheel is likely from worn tie rod ends. Have your inner and outer tie rods checked. The outer tie rods are connected to the rod ends coming out of the rack on each side, and are connected to the wheels. The inner tie rods are not visible-but are on the rods under the protective boots on each end of the rack and pinion assembly.
You may need a new rack assembly, but first check if you just need new tie rods.

Nov 25, 2013 | 1997 Honda Accord

3 Answers

There is power steering fluid dripping from the passenger side boot covering the rod that connects to the wheel. Could a simple replacement of the boot be the fix, or is there a problem with the main unit...


No, the boot only keeps dust out of the inner tie rod joint--it is not intended to hold back fluid. The rack will have to be rebuilt with new seals. Sorry. :o(

Dec 05, 2010 | 1998 Toyota Sienna

3 Answers

Can i replace a tie rod {inner} on a 94 ford mustang , drivers side without taking off rack and pinion. I need to get a roll pin off the inner tie rod and thats the problem it looks pressed in not set...


Real simple, assuming you know how to take the outer tie rods off. You have to take the clip that holds the plastic boot on off, then slide back the plastic boot, and you'll be able to unscrew the whole inner tie rod assembly. The hardest part of the whole process is installing the new ones to the exact settings of the old ones

Mar 13, 2010 | 1994 Ford Mustang

2 Answers

How do I install driver side inner tie rod on my 1997 chevy cavalier?No room to work. Do I need to remove whole rack and pinion assembly?


you don't need to remove the whole rack but do need a special tool called inner tie rod tool. can be bought or borrowed form most auto parts stores. first remove wheel. next loosen the jam nut on inner tie rod at the end of outer tie rod. remove cotter pin and nut on outer. use seperator or pickle fork to seperate outer from knuckle. then remove the clamps on boot and remove. then take tie rod tool and find the right size end and turn with 1/2" ratchet or breaker bar. it will turn hard at first cause of it being staked on to the threads. when it is off install new part with loc-tite on threads and tighten. when tight crimp inner flanges with either plier or hammer and punch to the rack. install in reverse order. remember to measure distance from clamp on outer side of boot to jam nut so you can get the alignment close until you get to shop for alignment.

May 05, 2009 | 1997 Chevrolet Cavalier

1 Answer

How do i change inner tie rod , do i need a special tool.


i think steering gear has to be removed to get rubber bellows off to access tie rod.

486d579.gif Section 11-02: Steering System, Power 1997 Continental Workshop Manual
DISASSEMBLY AND ASSEMBLY Tie Rod and Bellows SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Bench Mounted Holding Fixture T57L-500-B
Disassembly
  1. NOTE: Drill out mounting holes in holding fixture with a 9/16 inch drill to allow the power rack and pinion steering gear assembly mounting bolts to fit.

    Mount power rack and pinion steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Remove tie rod ends (3A130).
  1. sve~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care not to damage bellows. If bellows are damaged, this will allow contamination into the steering gear and cause leakage.
    Remove four clamps retaining bellows to steering gear housing (3548) and front wheel spindle tie rods (3280). Discard clamps if damaged or excessively corroded.
  1. NOTE: Steering gear does not use rivets or roll pins between the inner front wheel spindle tie rod and rack.

    Remove bellows along with power steering gear rack tube (3K762).
  1. Position power rack and pinion steering gear so that several steering gear teeth are exposed. Hold steering gear sector shaft (3575) with an adjustable wrench on end teeth only while loosening ball joint nuts.
Assembly
  1. Expose several steering gear teeth and hold steering gear with adjustable wrench.
  1. Tighten each front wheel spindle tie rod separately to 90-110 Nm (67-81 lb-ft).
  1. Thoroughly clean steering gear and steering gear housing bore of any foreign material. Any abrasive material is extremely harmful to high-pressure oil seals.
  1. Apply Steering Gear Grease C3AZ-19578-A or equivalent meeting Ford specification ESW-M1C87-A to groove in front wheel spindle tie rod where tie rod bellows clamp to front wheel spindle tie rod and uniformly to inner diameter of tie rod bellows before installation. This allows for toe-in adjustment without twisting tie rod bellows.
  1. Install tie rod bellows and power steering gear rack tube. Make sure power steering gear rack tube is positioned as shown.


    Power Steering Gear Rack Tube and Tie Rod Bellows Installation

Apr 04, 2009 | 1997 Lincoln Continental

1 Answer

Rack pinions and bushing installement


pretty decent job ahead first jack up car support with jack stands remove front wheels remove nuts on tie rod ends remove tie rod ends from spindles with tie rod end tool or tap with malet were they sit to loosen them hit the spindle area not the tie rod or tie rod threads then dissconnect power steering lines from steering rack also disconect steering linkage to rack there should be 2 main bolts holding assembly to frame remove them should free rack i know that car may have a unique design were u may have to remove inner tie rod ends first if it has those round bushings that always go bad disconect inner tie rod ends behind engine on top of steering rack then remove rack from wheel well replace those inner tie rod bushings u may be able to leave outer tie rod end connected to spindles and u may be able to get to the sterring rack from behind engine good luck

Mar 28, 2009 | 1997 Chrysler Concorde

1 Answer

How to replace Inner Tie rod on 1994 Chrysler Town & Country?


222,000 miles? that's a good vechile so far! anyways, do some price checking. new rack and pinions come with the inner tie rods. so if it's like 50 more for the whole assembly, i would but if not, it's up to you. i've changed some rack and pinions on vechiles that were under 150000 due to major leaking. and if you put just new rods in, if it dose start leaking later, you'll get new inner rods again with new system you'll just be paying labor and alingment charges again. so again, my OPINION is if I'm going to keep it for a while and if it's COST effective, just to do the whole unit.

Mar 07, 2009 | 2002 Chrysler Town & Country

1 Answer

Steering play


The possibilities are the rack and pinion,inner tie rods,outer tie rods,wheel bearings and balljoints but the most common parts replaced to fix this concern are the tie rods but that is not to say there is a combination of all the above.

Jim

Oct 09, 2008 | 1995 Ford Mustang

1 Answer

Inner tie rods


Most of the time when you are not able to get inner tie rod ends it's because you would have to replace the rack and pinion assy. to take care of the inner tie rod issue.

Jun 09, 2008 | 1989 Ford Festiva

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...