Question about 2001 Ford Explorer Sport Trac

1 Answer

My expolorer takes 3 or4 turns on the ignition before it starts

Posted by on

1 Answer

Check Fuel Pressure while cranking

Posted on Mar 13, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My holden commodore2007ve berlina has a problem when accelerate or going up hill has some hesitate or cut of fuel 3 or4 times while driving but I slow down every thing become normal


Hi This issue really requires a scan tool ( advise take to holden). There has been some cases where there has been an issue with the throttle body, this may not be the case with your's but its a good start point. if the throttle body checks out ok then i would require more information . Just another point are you sure its not fuel related it didn't start faulting after a recent refill. This may only show faulty under load.

Feb 12, 2017 | Holden Cars & Trucks

1 Answer

Ever 3 or4 miles i get a clunky grinding sound in my rearend of my truck


Check for:

* Loose, damaged or worn universal joint on the driveshaft

* An issue with the differential such as worn gears and/or fluid loss

* Check both axle bearings for wear or damage (If you have a bad axle bearing, you will usually hear it when you turn)

* Worn or damaged rear suspension component like a sway bar or stabilizer rod (if equipped)

Oct 05, 2015 | Cars & Trucks

1 Answer

1994 nissan altima GXE 10amp meter fuse blows with no regularity. Sometimes will not blow for a month other times will blow 3 or4 times a day


What system is the fuse blowing. There is a short in your system that is causing feedback into the system. For example:

1. A coin in a cigarette lighter will take out the Horn and Cruise control
2. Winding in the Fan Motor will short out as the hit bumps and short across multiple power sources

Need more information to answer completely

May 26, 2011 | Nissan Altima Cars & Trucks

1 Answer

My car died when i downshifted and would not start back up again....it tries and it's getting fire....i changed the fuel filter and pump and the spark plugs and wires...im at a dead end now.


Posting what size motor will help, if it is a 4 cyl V6 or whatever, and if its a 3 point something or4. something might help with an answer.












Mar 04, 2011 | 2003 Kia Spectra

1 Answer

I have two remotes, both needs to be reprogram, how do i do that whithout take to the dealer


hi, sometimes this is easy. put key in ignition turn key to IGNITION. DO'nt START IT. leave ignition ON for 3 seconds. then turn OFF . take key OUT of IGNITION wait 3 seconds and replace ignition key turn key to ignition. this is key recognition. some cars do and some cars do'nt. try this. gerry

Sep 13, 2010 | 2001 Volvo S40

1 Answer

Clutch goes all the way to the floor fluid comes out of cylinder under hood only shift when ignition is off


The problem is either the clutch master cylinder or the line going from the master cylinder to the clutch slave cylinder.Put some DOT 3 or4 brake fluid in the cylinder under the hood and have some-one look at it while you push the clutch pedal down a couple times. You should be able to see where it is you are losing the fluid.

Feb 19, 2010 | 1987 Nissan Pickup

1 Answer

As you drive it just stops and then will not start but 3 or4 hr latter it will


Replace crank sensor. If it stops pour or spray water on it and see if it will crank then you know what to do. The sensor is at the crankshaft pulley towards the front of car.

Jun 30, 2009 | 1991 Oldsmobile 88

1 Answer

2005 Expolorer won't start


When you say getting gas, how did you determine this?

Dec 31, 2008 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...