Question about Jeep Grand Cherokee

1 Answer

2001 grand cherokee 4.0l valve rocker torque specs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

5 million made.
it's in the fsm book
posted here over 300 times.
are you asking , how to set rockers ?

chapter 9 page 27
------------------text fsm---------------------
INSPECTION
Inspect the pivot surface area of each rocker arm.
Replace any that are scuffed, pitted, cracked or
excessively worn.
Inspect the valve stem tip contact surface of each
rocker arm and replace any rocker arm that is deeply
pitted.
Inspect each push rod end for excessive wear and
replace as required. If any push rod is excessively
worn because of lack of oil, replace it and inspect the
corresponding hydraulic tappet for excessive wear.
Inspect the push rods for straightness by rolling
them on a flat surface or by shining a light between
the push rod and the flat surface.
A wear pattern along the length of the push rod is
not normal. Inspect the engine cylinder head for
obstruction if this condition exists.
INSTALLATION
NOTE: This procedure can be done with the engine
in or out of the vehicle.
(1) Lubricate the ball ends of the push rods with
Mopart Engine Oil Supplement, or equivalent and
install push rods in their original locations. Ensure
that the bottom end of each push rod is centered in
the tappet plunger cap seat.
(2) Using Mopart Engine Oil Supplement, or
equivalent, lubricate the area of the rocker arm that
the pivot contacts. Install rocker arms, pivots and
bridge above each cylinder in their originally position
(Fig. 23).
(3) Loosely install the capscrews through each
bridge.
(4) At each bridge, tighten the capscrews alternately,
one turn at a time, to avoid damaging the
bridge. Tighten the capscrews to 28 N·m (21 ft. lbs.)
torque.
(5) Install the engine cylinder head cover (Refer to
9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD
COVER(S) - INSTALLATION).

Posted on Feb 21, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2692 Answers

SOURCE: Torque Specs

Torque: 210 @ 4000 rpm

Posted on Dec 22, 2008

  • 512 Answers

SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

sirgabe51
  • 66 Answers

SOURCE: I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


e023442.jpg

Posted on Dec 05, 2009

tneubauer
  • 437 Answers

SOURCE: i need torque specs on 93 dodge 360 ..heads,

Cylinder Head Bolt 5.9L

Step 1 - 50 ftlb
Step 2 - 105 ftlb
Step 3 - Recheck At 105 ftlb

Tightening sequence

Rocker Arm Bolt

5.9L - 17 ftlb

Posted on Jan 23, 2010

ZJLimited
  • 17970 Answers

SOURCE: need torque specs for a 2001 jeep cherokee intake

Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lifter tap on a gmc sonoma 2.2 its a2001


U R GONNA NEED A FIELER GUADGE AND THE VALVE LASH SPEC REMOVE THE VALVE COVERS AND INSERT THE GUADGE BEWEEN THE ROCKER ARM AND VALVE SPRING AND TORQUE TO SPEC OR TAKE OFF VALVE COVER TAKE TWO PIECES OF CARDBOARD CUT THEM TO LENGTH OF THE HEAD INSERT ON TI THE HEAD SO U DONT SPASH OIL START TRUCK AND TURN EACH ROCKER UNTIL YOUR NOISE GOES AWAY BUT DO NOT OVER TORQUE U WILL KNOW THE ENGINE WILL BOGG DOWN

Jan 18, 2013 | 2001 GMC Sonoma Extended Cab

1 Answer

How do I adjust the valves on a 1998 old bravada 4.3 vortec


You don't. They are non-adjustable hydraulic lifters. GM's spec for torque on the rocker arm nuts: Tighten the valve rocker arm ball studs to 47 N·m (35 lb ft). Once the valve rocker arm nuts are installed and properly torqued, no additional valve lash adjustment is required.

Aug 05, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

Lifter torque specs? 1994 5.2l grand cherokee 4x4. need to know how tight to torque them.


I think you mean the rocker arms. 21 Ft/Lbs. If your talking about the "yoke retainers" then they get torqued to 200 INCH lbs.

Jun 26, 2011 | 1994 Jeep Grand Cherokee

2 Answers

Rocker arm torque specs on a 2001 chevy malibu 3.1


Rocker arm torque specs for the bolts are 14 Nm (124 inch lbs.)

Apr 15, 2011 | 2001 Chevrolet Malibu

2 Answers

Rocker arm toruge specs, how many lbs?


FOR THE 242 -4.0 ENGINE ROCKER ARM TORQUE IS 21 FT LBS FOR THE 5.2L AND 5.9L ENGINES ROCKER ARM TORQUE IS 21 FT LBS.

Aug 04, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

1 Answer

What is the torque specs on intake and manifold bolt on a 2001 jeep cherokee engine is 4.0


Call Autozone or a major parts retailer. They will give you the torque/tightening sequence for free.

Mar 07, 2010 | 1993 Jeep Grand Cherokee

2 Answers

2004 pontiac grand am 3.4 rocker arm torque?


the rocker arm torque specs for the la1 gm 3400 sfi v6 is 168in lbs or 14ft lbs and 30degrees past that hope that helps you it came straight from my local dealer!

Apr 05, 2009 | 2004 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...