Question about GMC Yukon

1 Answer

How To Install Distributor cap and rotor on a 1999 GMC youkon

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 232 Answers

Best thing and I tell everyone this ,,,,if your going to be your own mechanic buy your self a Hayes manual for that vehecle,,Only 15 $ at Auto Zone, in there is all info you will ever need.

Posted on Mar 13, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Install Replace Distributor Cap & Rotor Chevy GMC Vortec 5700 1AAuto.com


How To Install Replace Distributor Cap & Rotor Chevy GMC Vortec 5700 1AAuto.com

on Mar 29, 2012 | 1988 Chevrolet Silverado 2500

1 Answer

Como cambiar distribuidor gmc safari 2001


Remove the distributor cap. Mark the location where the rotor is pointing by making a scratch mark on the distributor housing. Remove the distributor adjusting bolt and bracket. Remove the distributor. Replace with the new distributor by placing the rotor on the shaft and turning the shaft until the rotor aligns with the same place as the mark on the old one. Install the bolt and tighten. Start engine. If your engine does not run, remove the bolt and distributor and turn it 180 degrees and replace.

Mar 11, 2011 | GMC Safari Cars & Trucks

1 Answer

Where is the cam sensor located


Removal & Installation 2.2L Engine To Remove:
  1. Lift the vehicle.
  2. Remove or disconnect the following:
    • Right wheel and tire assembly.
    • Camshaft position (CMP) sensor electrical connector. gm_truck_s10_cmp.gif

    • Bolt and CMP sensor.
To Install:
  1. Install or connect the following:
    • Camshaft position (CMP) sensor and bolt.
      1. Torque to: 7 ft. lbs. (10 Nm)
    • CMP sensor electrical connector.
    • Right tire assembly.
  2. Lower the vehicle.
4.3L Engine To Remove:
  1. Remove or disconnect the following:
    • Spark plug wires and ignition coil wire from the distributor 4.3L Distributor CMP electrical connector gm_trk_sil15_02-04_43_dist_cmp_elect_conn.gif

    • Camshaft position (CMP) sensor harness connector from the distributor
    • Distributor cap screws 4.3L Distributor cap removal gm_trk_sil15_02-04_43_dist_cap_rem.gif

    • Distributor cap 4.3L Distributor rotor screws removal gm_trk_sil15_02-04_43_dist_rotr_screw_rem.gif

    • Rotor screws
    • Rotor
    4.3L Align reluctor wheel slot with CMP gm_trk_sil15_02-04_43_algn_whl_slot_cmp.gif

  2. Align the square slot in the reluctor wheel with the CMP sensor 4.3L CMP sensor screws removal gm_trk_sil15_02-04_43_cmp_sensr_screw_rem.gif

  3. Remove or disconnect the following:
    • CMP screws 4.3L CMP sensor removal gm_trk_sil15_02-04_43_cmp_sensr_rem.gif

    • CMP sensor
To Install:
NOTE: Do not use the old cap, CMP sensor, and rotor screws. Use the replacement screws that have been coated with a thread locking compound.
  1. Insert the CMP sensor through the reluctor wheel slot
  2. Install or connect the following:
    • New CMP mounting screws and tighten the screws
      1. Torque to: 19 inch lbs. (2 Nm)
    • Rotor onto the reluctor wheel
    • New rotor screws and tighten the screws
      1. Torque to: 18 inch lbs. (2 Nm)
    • Distributor cap
    • New distributor cap screws and tighten the screws
      1. Torque to: 21 inch lbs. (2.4 Nm)
    • CMP sensor harness connector
    • Spark plug wires and ignition coil wire
  3. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 17, 2010 | 2000 GMC Jimmy

1 Answer

Just got answer from Matthew about replacing distributor cap on 1999 Sebring. Thanks, but what I really needed to know is if the intake manifold and all the other parts that eneded to com off to replace 3...


Not sure about your engine size so please pick your model:

2.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Bolt holding air inlet resonator to intake manifold.
    • Clamps holding air cleaner cover to air cleaner housing.
    • PCV make-up air hose from air inlet tube.
    • Hose clamp at throttle body.
    • Air inlet tube, resonator and air cleaner cover.
    • EGR tube.
    • Spark plug cables from distributor cap.
  3. Loosen distributor cap hold down screws and remove cap
    NOTE The rotor is friction-fitted to the distributor shaft and can be pulled straight off.

  4. Transfer cables from old cap to new cap. The cap and cables are numbered with their corresponding cylinder numbers.
f50a560.gif
Distributor cap—2.5L and 3.0L Engines

To install:

  1. Install or connect the following:
    • Distributor cap.
    • Distributor holddown washers and nuts and torque to 9 ft. lbs (13 Nm)
    • EGR tube.
    • Air inlet tube, resonator and air cleaner cover.
    • Hose clamp at throttle body.
    • PCV make-up air hose from air inlet tube.
    • Clamps holding air cleaner cover to air cleaner housing and securely tighten.
    • Bolt holding air inlet resonator to intake manifold and securely tighten.


3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Air cleaner
    • Spark plug cables from distributor cap.
  3. Loosen distributor cap hold down screws and remove cap
    NOTE The rotor is friction-fitted to the distributor shaft and can be pulled straight off.

  4. Transfer cables from old cap to new cap. The cap and cables are numbered with their corresponding cylinder numbers.
To install:

1ac2d69.gif
Distributor cap—2.5L and 3.0L Engines

    1. Install or connect the following:
    2. Distributor rotor
    • Distributor cap
    NOTE Make sure the new cap has an O-ring in its base.

    • Distributor holddown washers and nuts and torque to 20 inch lbs. (2.3 Nm)
    • Air cleaner
  • Oct 26, 2009 | 1999 Chrysler Sebring

    1 Answer

    Intake manifold leaking antifrezze . 1999 GMC Suburban 5.7. Antifrezze leak on passenger side. It looks like coming from intake. Not sure. If I do this myself do I have to distributor out and if so how do...


    BEFORE YOU REMOVE DISTRIBUTOR,MARK THE POSITION OF #1 DISTRIBUTOR CAP TOWER TO DISTRIBUTOR..REMOVE CAP AND TURN ENGINE TO LINE UP ROTOR BUTTON WITH THIS MARK..MARK DISTRIBUTOR HOUSING IN RELATION TO HOLD DOWN CLAMP OR BOLT..YOU CAN USE A PAINT PEN OR EVEN SOME WHITE OUT..YOUR TIMING SHOULD BE CLOSE TO WHRE TO WHERE IT WAS..I HOPE THIS HELPS

    Sep 03, 2009 | 1999 GMC Suburban

    1 Answer

    1999 gmc safari doesnt have a spark


    replace the distributor i had the same problem

    Jul 23, 2009 | 1999 GMC Safari

    1 Answer

    Timing on vortec 350youkon how to do this


    unplug distributor! find #1 cylinder, take out spark plug,placr finger over spark plug hole,bump starter until compression blows finger from spark plug hole,align mark on harmonic balancer with 0 mark on timing cover. engine is on compression stroke.install distributor with rotor contact pointing toward #1 wire location on distributor cap. install plug. install wire. engine will start.

    May 11, 2009 | Chevrolet Suburban Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    53 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...