Question about GMC Jimmy

1 Answer

Its using a lot of gas and runs rough at times. SES light came on and the code is po141.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

That code means that the Ox2 sensor is bad or a wire has broken to it (most likely a bad Ox2 sensor). It is the Bank 1 sensor 2 Ox2 sensor See picture for location. its using a lot of - mcneb_22.jpg

Posted on Mar 13, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 97 deville concours with northstar that keeps giving me a P0300 code and SES light?

cars seldom idle rough when warming up if the injectors and electronics are in good condition
P0300 refers to random misfires which is the rough idle when warming up
the history in the fault codes is the fault report generated but not maintained as the fault rectifies itself
the ses is probably telling you to service the system--clean the injectors , fuel filter or check fuel pressure

Jan 05, 2017 | Cars & Trucks

1 Answer

Got a Code 43 on my 1992 Buick Regal Custom.

sometimes is hard to get there and cost a lot of money.

Mar 08, 2013 | Cars & Trucks

1 Answer

My 2003 Pontiac Grand Am GT has a flashing and sometimes a Solid SES light and runs rough

Usually with the newer vehicles when it starts to run rough or idle poorly it's time for a tune up, that will also make the check engine light come on on some vehicles, it needing an oil change can also cause the light

Dec 07, 2012 | 2003 Pontiac Grand Am

2 Answers

I wa driving to work and when i left the parking lot while i was accelerating the ses light started flahing and now the car is running rough. what can it be

It can be a number of things. The way to find out what is to hook a code reader or scanner to it and find out what code(s) are in the PCM. Until that is done, anythig else would just be guess work.

Aug 29, 2011 | 1996 Chevrolet Camaro

1 Answer

The GLS with a 3.4 engine is running rough. It will idle high (sounds like a chain saw) with lots of exhaust. It will "hiccup" going 60 mph. The service engine light comes on when it...

I had a similar problem on my Aurora 4.0. These had a common problem with the air intake plenum gasket leaking. The car, in this condition, couldn't measure the air flow properly and the result was a poor air/fuel mixture. This is easily seen with an ODB-II scanner looking at the fuel trims and O2 sensors.
The SES light means you are getting CODES. These are certainly going to lead you in the right direction.
The hiccup sounds to me like maybe a crankshaft position sensor - you should get this fixed ASAP if it is, as you can trash the engine if you don't. It will throw the appropriate code, so start with getting the codes scanned.

Jan 24, 2011 | 1999 Oldsmobile Intrigue

1 Answer

Ses light flashing, truck running rough

Good Evening. I'm sorry to hear your truck is running bad, however I can give you a few points to check on. Your flashing SES light is because you have a misfire in your engine. The misfire could be caused from things like spark plugs and wires or a cap and rotor, low fuel pressure or bad gas. Or the other things like an intake leak or a bad valve so diagnosing is harder without the code that is set while your SES light is on. So get a scanner hooked up and see which cylinder it says is misfiring and go fron there back to the wire to the cap etc. Hope this helps and if you have any more questions please feel free to ask.

Aug 26, 2010 | 1997 GMC Sierra

1 Answer

My gmc envoy idles rough and the ses light pop on with a p015

See or call your local auto parts store such as AutoZone or O'Reillys for the trouble code definition. Also, make sure your gas cap is really secure, and I mean tight.

Apr 16, 2010 | 2003 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

75066 Answers


Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides