Question about 2004 Nissan Maxima

Open Question

The presets on my memory seats do not work anymore. when i press the button the green lights do not go on. almost as if there is no power going into them. the wiring harness is connected. this happened after an aftermarket alarm system was installed. But no wires that relate to the seat, mirrors, steering wheel, were touched. the only problem i can think is the memory seat preset buttons were piggybacked on a running wire to something else was cut. after a search other suggested it is something that needs to be reset or reprogrammed, body control module or something but if this is the case there should at least be power going to the lights on the buttons.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 45 Answers

SOURCE: steering wheel audio controls wires

those controls will only work with your factory audio unit not aftermarket ( it has an interphase )

Posted on Aug 28, 2008

Ad
  • 2 Answers

SOURCE: 1985 300zx antenna & wiring

On the fuse box behind the driver side left kick panel find the Radio fuse and connect the main power to that remember to keep the full time power connected to the proper wire so your clock (if you raido has one) will keep correct time. If you are not sure which wire on the radio is full time power and which is the on off power check the manufacture web site for information or call there help line. From the radios I have done and I am no expert beleave me but the ones I remember always used Red for the main power (the one that should be switched so the radio comes on with the key and not have to be turned on and off) the full time power for the clock and memory features is usualy yellow. Black or green can be ground but use caution as these could also be speaker wire colors. If you cant find the fuse location from the original radio you can use a simple volt meter or just a 12 volt light blub with two wires attached. simply take the negitive side and place that wire on a bolt that is screwed into the car metal body or frame or to a known ground wire. take the positive end and start touching the positive wires on the back on fuse box. if you start with the key off you know everyone that lights up has constant power so mark them with one color perminate marker. next turn the key to ACC. and see which of the non marked have power and again mark them with a different color (one of these will be the one you want to use just make sure you pick one with a small fuse as most radios will melt long before a #25 fuse blows again check the manufactures spesifications for the proper fuse range to use. Now the only thing left to do is to turn the key to on and make sure the power sorse you plan to use stays on withthe key in on as well as acc. now connect the red wire to the source chosen and leave everything else alone and you sould be fine. I can stress this enough you should always check with the manufacture of the radio before playing with the wires to make sure you dont put the wrong one in the wrong place because doing so can dammage the radio of worse your car. Also keep in mind I am not a professional and am offering the way I would approch this problem if it were me doing it. If possable your best bet is to take the car to a professional so you have some assurances it is done correctly and you wont come out one day to find your car has caught fire and is a pile of ash because you put this wire where that one went and didnt notice anything. Good luck

Posted on Jan 12, 2009

  • 491 Answers

SOURCE: I have a 04 nissan

CHECK FOR ANY WATER COTACT WITH WIRING

Posted on Jul 20, 2009

pops296
  • 174 Answers

SOURCE: Wiring problem for 2005 Pathfinder trailer hitch

Sounds like the converter is bad. Go to http://www.etrailer.com/faq-wiring.aspx and check the testing section. Hope this helps.

Posted on Jan 29, 2010

  • 1 Answer

SOURCE: Wiring for Bosch Hologen Fog Lights? Wiring

Look on the relay for the terminal numbers.
Terminal 30 goes to the battery positive.Red Wire
The two terminal 87 go to the fog lights.Black Wires
Match the color wire with what you have on the relay connection for the rest of the wires.
Terminal 86 should connect to your low beam headlight.
Terminal 85 should go to the fog light switch.
The fog light switch should connect to the terminal 85 and the other terminal on the switch will connect to ground.

Posted on Feb 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I manually set my radio stations to my rcart2770 reciever


1. Connect the FM antenna and the AM loopantenna at the back of the unit. Rotate the AM loop for better reception.
2. Press AM/FM.
3. Tune a station by pressing TUNER+/-repeatedly until the desired station is found.Alternatively, you can press and hold thesame buttons down for about one second toactivate the automatic search function. Inthis mode the unit will automatically tunefrequencies until it finds a station.
4. Repeat step 3 to tune to another radio station.
5. Press AM/FMto select between FM and AM.Storing Radio Stations

The unit can store up to 40 radio stations (30 preset stations for FM and 10 preset stations for AM) in its memory. You can enter every single radio station yourself or the unit can store all available radio stations automatically in ascending order

Automatic Preset Programming
1. Press AM/FM to enter the AM/FM mode.
2. Press and hold AM/FM for two seconds to start automatic preset programming.
3. Radio frequencies will be browsed and radiostations stored automatically. When all the available radio stations are stored or all 40(30 preset stations for FM and 10 preset stations for AM) memory locations are full,the auto preset programming function will stop.

Manual Preset
1. Tune to a radio station (see "Manual tuning"for details).
2. Press MEMORY. While the Program Preset number is still flashing, input your desired preset number using the numeric buttons or press CH+/-, then press MEMORY to store it.

Retrieving Preset Stations
1. Press AM/FM to enter the Tuner mode.
2. Press CH +/- to search up or down for thepreset stations or directly press the numeric buttons.

Apr 30, 2014 | Cars & Trucks

2 Answers

Side Mirrors


is there a preset option on this model if so you will have to set mirrors where you want them as it may be reseting to a previous setting , how long has this been happening ?

Mar 31, 2014 | 2005 BMW X5

1 Answer

2004 Envoy XUV heated seats do not work on both sides. I press the button and the lights come on, when i release the button the lights go out. I checked the fuses mentioned in the articles on this site but...


If other functions such as window controls and power seat controls are normal, here are some possibilities;
1) Circuit Breaker #8 in rear fuse panel
2) Defective Driver Memory Seat Module (under driver's seat)
3) Break in data lines between Driver's Memory Seat Module and Drivers Door Module
4) Fuse 23 & 6 in rear fuse panel

Nov 13, 2012 | 2004 GMC Envoy

7 Answers

The electric adjustment on my driver seat in my JEEP 2006 - Grand Cheroke, re-sets itself to a lying down position every time I use the vehicle. So each time I get in I have to spend 2-3 minutes...


There is no need to go disconnecting the battery as Leonard Javier has suggested above. If your Jeep is equipped with a driver's memory seat, the memory can be cleared at any time using the controls provided by the manufacturer.

How you would go about doing this is covered in the 2006 Jeep Grand Cherokee Owner's Manual, begining on page 114.
If you do not have an Owner's Manual for your Jeep, you can download a PDF version of it for FREE at the following URL.

http://www.jeep.com/en/owners/manuals/

Nov 01, 2011 | 2006 Jeep Grand Cherokee

1 Answer

My Escape Radio, CD, and Aux input will not work. My temp gauge works, but all music controls do not, except for the load and eject buttons for the CD player. I replaced three fuses that according to my...


Which three fuse's did you replace ? You should check for B+ voltage on both side's of the fuse . Two little metal tabs on top of the fuse. Voltage on both , fuse is good .
Try radio self-diagnostic mode .
A fluctuating AC voltage audio signal is sent to the speakers directly from the audio unit to reproduce sound. The audio unit has a self-diagnostic mode that can be entered by pressing preset buttons 3 and 6 simultaneously.
Visual Inspection Chart Mechanical Electrical
  • Audio unit
  • Antenna or antenna cable
  • Speaker mounting/speaker cones
  • Radio ignition interference capacitor, radio frequency interference suppression bond, or radio receiver hood bonding strap
  • Smart junction box (SJB) fuse(s):
    • 7 (10A)
    • 12 (5A)
    • 16 (15A)
  • Battery junction box (BJB) fuse(s):
    • 7 (40A)
    • 15 (20A) (Hybrid)
    • 16 (25A)
    • 21 (40A)
    • 22 (40A) (Hybrid)
    • 23 (40A) (Hybrid)
  • Subwoofer amplifier
  • Circuitry
  • Audio unit

  1. If the concern is visually evident, GO to Symptom Chart .
  1. If the concern is not visually evident, proceed to the Speaker Walk-Around Test and the Audio Unit Self-Diagnostic Mode.

Speaker Walk-Around Test (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in the radio tuner mode (AM/FM).
  1. To enter the speaker walk-around test, simultaneously press the audio unit preset buttons 3 and 6.
  1. The speaker walk-around test stops at each speaker and applies sound to each speaker for about 1-2 seconds. Each speaker is tested and displayed on the audio unit in the following sequence: RF, LF, LR, RR and SUBWOOFER.
  1. To exit the speaker walk-around test, turn the ignition switch off, turn the audio unit off, or press preset button 1 for diagnostics (DIA).

Audio Unit Self-Diagnostic Mode (Except Premium CD6)
NOTE: To enter the speaker walk-around test or audio unit self-diagnostic mode, the audio unit must be turned on and in radio tuner mode (AM/FM).
  1. To enter the following tests, press the desired preset button while in the speaker walk-around test or while in the audio unit self-diagnostic mode.
  1. To exit the audio unit self-diagnostic mode, turn the ignition switch or the audio unit off.
  1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.
  1. The self-diagnostic mode has 6 manual tests available:
    • Preset button 1 = ENTER DIAGNOSTICS. This test enters diagnostics from the speaker walk-around test. Metrics are available with SEL and ON buttons indicating time played in AM/FM, media, number of buttons pressed, etc.
    • Preset button 2 = EEPROM BLOCK STATUS. This test shows the validity of memory to calibrate the clock, and seek sensitivity.
    • Preset button 3 = EXIT DIAGNOSTICS.
    • Preset button 4 = Software configuration level. This test queries each radio system controller for its software configuration level.
    • Preset button 5 = DISPLAY TEST. This test lights all the display segments for five seconds and then turns all segments off.
    • Preset button 6 = RAM CONTENTS READOUT. To enter these tests, press preset button 1 while in the speaker walk-around test, then the desired preset button.
  1. To exit the self-diagnostic mode, turn the audio unit or the ignition switch off.
  1. If the concern remains and the fault is not detected, GO to Symptom Chart to continue diagnostics.

Oct 06, 2017 | 2008 Ford Escape

1 Answer

Power seat doesnt work 2005 f150


If you have the memory seats, there are 2 fuses to check, Fuse #3 and Fuse # 109 or 108 ( drivers or pass ). 108 & 109 are for the non memory seat version ( the driver's side seat has the 1 & 2 buttons on it, on the side ).

If both of these check OK, there are 2 routes.
1. Check for power at the power seat module
1.1. Fuse #3 = pin #1, Orange w/ light green stripe wire.
1.2. Fuse # 109 = pin #1 ( on the other connector ) Dark Green wire.
Both are hot at all times, key position does not matter.

The non memory seat version is just fuse #109, Dark green.

Route #2 is some times there is a water leak in the driver's side door sill. There is a wire that is spliced ( 1 in, 2 out ) that can corrode and break. If this happens, there are usually other symptoms ( open door will not shut of radio, power mirrors don't work, etc ).

Lacking other symptoms, Focus on those 2 fuses, and making sure power is under the seat at the connector.

Oct 24, 2009 | 2005 Ford F-150

1 Answer

I have no owners manual for my 2000 Mercedes S500. How do you change the radio station presets? What are the 1,2,3 numbers on the seat bottoms and how to use them? What is the ESP button for on the dash?...


To set the stations you just tune in to the station and hold the preset number button until it locks in. The numbers on the seat bottoms are presets for the seats. Put the seat into what ever position, you should also have a round green button, push that then push a number. Change the seat position and when you hit that number/hold the button it should go back to that position. ESP is traction control on the vehicle, it allows to disable it for snow at low speeds when wheel rotation is needed when known slippage will most likely occur.

Aug 05, 2009 | 2000 Mercedes-Benz S-Class

1 Answer

94 toyota 4 runner radio says help


Turn the key to ACCY

Press at the same time: POWER, preset buttons 1, 4 and 6.

Prtess and hold the TUNE ^ (up arrow) button.

until ^ _ _ _ appears on the display.

using the preset buttons 1,2 and 3, input the first 3 digits of the 6 digit code. Each press will move the digits.

After you have the first 3 digits input, Press the Tune/down arrow and 1 until there is a down arrow and _ _ _

Input the last three digits using the 1,2,3 memory presets

When that is done, press and hold the SCAN button until SEC appears, and goes blank. The radio is now operational..

Apr 06, 2009 | 1993 Toyota 4Runner

1 Answer

2003 Lexus ES300 How does one save Radio Statio presets? Going to the station and holding the button to save does not work.


Holding the button is supposed to work. This from owner's manual: PRESETTING A STATION:
  1. Tune in the desired station.
  2. Push one of the station selector buttons (1-6) and hold it until a beep is heard. This sets the station to the button and the button number (1-6) appears on the display.
Each button can store one AM station and two FM stations. To change the preset station to a different one, follow the same procedure. The preset station memory is cancelled when the power source is interrupted by battery disconnection or a blown fuse.

Jan 08, 2009 | 2003 Lexus ES 300

1 Answer

1996 cadillac seville power seat problems


Because that switch is broken and stuck in the recline mode.

Dec 16, 2008 | 1991 Cadillac Fleetwood

Not finding what you are looking for?
2004 Nissan Maxima Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...