Question about Saturn L300

Open Question

03 saturn L300 got trouble code p0341 which is timing sensor where is it located

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ecmurphy10
  • 53 Answers

SOURCE: p0341

This is a very labor intensive job that requires you to take the head off of the block. I would take it into see a engine specialist.

Posted on Jan 20, 2009

  • 73 Answers

SOURCE: flasher/2002 saturn l300

youturn signal flasher is part of the hazzard switch located in the center of the dash above the radio. the trim piece around the radio and the climate controls pops off using a small flat bladed scewdriver.

Posted on Mar 31, 2009

  • 299 Answers

SOURCE: 99 Saturn with trouble code P0341

cam position code ,ingnition coil for 1&4 plug,probably fail plug wires or corrosion at coil and plug wires. could also be cracked 1or4 sparkplug.

Posted on Jun 16, 2009

  • 543 Answers

SOURCE: '99 Saturn SC1 with intermittant check engine light P0341

a p0341 code mean cam reference performance, really it means you have a secondary ignition problem,,,,like a bad ignition module
a bad crank sensor
a high resistance spark plugs,do not use bosch platinum plugs in these cars
high resistance spark plug wires,,,i work at the dealer and the first thing we do is replace the spark plugs and wires if that dont work we replace the crank sensor,if thatdont work we reaplce the ignition mondule,and by then your fixed and you started with the cheapest items first,,,i would try plugs and wires and a crank sensor,,,,wires $50 plugs $14 crank sensor $37

Posted on Oct 23, 2009

wracefans24
  • 1985 Answers

SOURCE: what do codes p0335 and p0341 mean on 1996 Cavalier?

when your engine went into that 5 second sputter,
your computer or "PCM" did not get a constant signal from the crank or cam sensors that the engine was running.
These two sensors tell the computer what RPM the engine is turning so it can adjust fuel and spark.

Posted on Nov 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is code p0341


DTC P0341: Camshaft Position Sensor "A" Circuit Range/Performance B1
Probable cause:
  1. Sensor or solenoid faulty
  2. Connector terminal contact damaged or corroded
  3. Wire harness fault. Check for correct voltage, open, short to ground or short to voltage
  4. Update control unit software - Check for the latest control unit update
  5. PCM or ECM faulty

Jul 05, 2017 | Saturn Cars & Trucks

1 Answer

WHAT IS THE CODE P0341


This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Symptoms The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
  • Poor fuel economy (if engine runs)
  • Possible no start condition
Causes A code P0341 may mean that one or more of the following has happened:
  • Cam sensor wiring routed too close to spark plug wiring (causing interference)
  • Poor wiring connection at cam sensor
  • Poor wiring connection at PCM
  • Bad cam sensor
  • Damaged reluctor wheel
Possible Solutions Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
  • Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
  • Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
  • Visually inspect the cam sensor for damage
  • Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
  • If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
  • If all checks out okay, then replace the sensor.
Related Camshaft Trouble Codes: P0340

Mar 07, 2012 | 1996 Saturn SL

1 Answer

I have three trouble codes p0133-p0113-p0341 i need to know what to buy to fix my car


CODE PO113 - INTAKE AIR TEMPERATURE SENSOR INPUT ABOVE MAXIMUM ACCEPTABLE RANGE. CODE PO133 - UPSTREAM OXYGEN SENSOR RESPONSE SLOWER THAN MINIMUM REQUIRED SWITCHING FREQUENCY. CODE PO341 - CMP SENSOR SIGNAL RANGE PERFORMANCE CONDITIONS. POSSIBLE CAUSE COULD BE CAMSHAFT POSITION SENSOR FAULTY OR PCM FAULTY GOT TOO MANY CODES. LET DEALERSHIP CHECK IT OUT USING DIAGNOSTIC EQUIPMENT. YOU DONT WONT TO BUY ALL THOSE SENSORS IF PROBLEM ELSE WHERE THE COST WILL ADD UP THAT WHY LET DEALERSHIP CHECK IT OUT.COULD BE THE PCM OR SHORT IN WIRING.

Jun 01, 2011 | 2001 Saturn S-Series

1 Answer

1998 saturn sc2 po341


P0341 - Camshaft Position Sensor Circuit Range/Performance

This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

Symptoms: The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in "limp-in/limp-home" mode even with a cam sensor signal problem. There may be no noticeable symptoms other than:
* Poor fuel economy (if engine runs)
* Possible no start condition


Causes: A code P0341 may mean that one or more of the following has happened:
* Cam sensor wiring routed too close to spark plug wiring (causing interference)
* Poor wiring connection at cam sensor
* Poor wiring connection at PCM
* Bad cam sensor
* Damaged reluctor wheel

Possible Solutions: Often relacing the sensor fixes this code, but not necessarily. Therefore it's important to check the following:
* Check that the wiring isn't routed too close to any secondary ignition components (coil, spark plug wires, etc.)
* Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing
* Visually inspect the cam sensor for damage
* Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage
* If reluctor isn't visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design)
* If all checks out okay, then replace the sensor.

Related Camshaft Trouble Codes: P0340


Hope helps (remember to rate this answer).

Jan 03, 2011 | Saturn SC2 Cars & Trucks

1 Answer

1998 Saturn problem code P0341


P0341 Camshaft Position Sensor Circuit Range/Performance.

most likely the sensor is bad

Jan 06, 2010 | 1998 Saturn SL

1 Answer

'99 Saturn SC1 with intermittant check engine light P0341


a p0341 code mean cam reference performance, really it means you have a secondary ignition problem,,,,like a bad ignition module
a bad crank sensor
a high resistance spark plugs,do not use bosch platinum plugs in these cars
high resistance spark plug wires,,,i work at the dealer and the first thing we do is replace the spark plugs and wires if that dont work we replace the crank sensor,if thatdont work we reaplce the ignition mondule,and by then your fixed and you started with the cheapest items first,,,i would try plugs and wires and a crank sensor,,,,wires $50 plugs $14 crank sensor $37

Oct 23, 2009 | 1993 Saturn SC1

1 Answer

99 Saturn with trouble code P0341


cam position code ,ingnition coil for 1&4 plug,probably fail plug wires or corrosion at coil and plug wires. could also be cracked 1or4 sparkplug.

Jun 12, 2009 | 2000 Saturn SL

1 Answer

Solution for 1998 saturn sl


Hello DTC P0341 & P0133 very common saturn Codes.You need to check condition of Plugs & wires,If not New Replace All Plugs & Wires,also I would replace the #1#4 Coil for the P0341.For the P0133 Reaplce your front O2 sensor with an OEM sensor,not an aftermarket.

May 03, 2009 | 1998 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...