Question about 1992 Oldsmobile Cutlass Supreme

1 Answer

How to remove crank sensor ? 1992 with a 3.1 found sensor on back of engine but how do i get to it and remove ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 130 Answers

It has a 10mm bolt to remove then you easily pry it out

Posted on Mar 13, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i get rid of engine code 13 on my 1992 Lexus LS400

You change no parts

The only parts that get replaced, are
those that fail a test

Have a repair shop take over & find a problem
thru proper testing vs: a wish & hope strategy
on a guess, by replacing good parts

Nov 21, 2014 | 1992 Lexus Ls 400

1 Answer

Where is crank sensor located on my 1992 grand prix le

the 3.8 behind the front crank pulley 3.1-3.4 on the back side of the engine between the engine and trans

Sep 23, 2012 | 1992 Pontiac Grand Prix

1 Answer

Picture of engine of 1992 buick 3.8 crank shaft posistion senser

you have to remove the harmonic balancer on the crank shaft to remove the sensor.
you will need a harmonic balancer puller.

Oct 07, 2011 | 1992 Buick LeSabre

1 Answer

1992 Chavy Cavalier 2.2L engine. No Spark

This could be a few things, you will need to do some testing, fist check all grounds and connections to crank sensor and the module also remove computer connector and make sure pins on connector and computer are good and not broken, from there remove the module and have it tested. a lab scope would be needed to test crank sensor and a multimeter to test coils,this is going to take some testing you could have a bad module or crank sensor or coils or computer,

Feb 26, 2011 | 1992 Chevrolet Cavalier

1 Answer

How to test crank sensor and ecu 0n 1992 eclipse 1.8L . Cranks has no spark.

connect a test light to the plug on the ignition coil with it disconnected and crank the engine. if the light flashes the crank sensor is ok and you should replace the ignition coil. if it doesnt i would replace the crank sensor.

Nov 17, 2009 | 1992 Mitsubishi Eclipse

1 Answer

Engine dies while moving

when it dies try spraying the crank sensor with brake cleaner to cool it down if it starts right back up then replace the sensor....... ALSO These cars are known for bad ground wires.....remove the kick panel on the drivers side pull the carpet back there is a thin black piece if plastic with a bunch of black wires going to it pull it apart and clean the metal piece inside with sand paper apply electrical contact grease put it back together this ground causes many problems

Oct 11, 2009 | 1992 Pontiac Bonneville

1 Answer

1992 Ford Taurus wagon not starting, but turns over

You might have a problem with your crank sensor or ignition. Remove spark plug wire and check for spark while turning engine over. When this happens unplug crank sensor near crank pulley then plug back in to see if it starts if so replace crank sensor.

Jul 29, 2009 | 1992 Ford Taurus

2 Answers

I need to replace the crank sensor on my 1992 chevy lumina the only problem is i cannot get the old crank sensor off

  • Disconnect the wiring harness.
  • Unbolt the sensor mounting bolt.

Jan 31, 2009 | 1992 Chevrolet Lumina

1 Answer

1992 chevy cavalier, 4 cyl. crank system sensor

The crank sensor is under the oil sending unit on the back of the motor next to the firewall. It is held in the block by an 8mm bolt. It has to be removed from under the car. Get under the car on the RH side and get back far enough that you can see over the transaxle. Good Luck.

Dec 17, 2008 | 1992 Chevrolet Cavalier

2 Answers

Crank sensor

The crank sensor is behind the harmonic balancer. Not too hard to replace, the harmonic balancer is supposed to come right off but I needed a big 2-jaw puller to get it off.... accessed through the wheel well.

Jul 11, 2008 | 1992 Oldsmobile 88

Not finding what you are looking for?
1992 Oldsmobile Cutlass Supreme Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides