Question about 2000 Honda Accord

1 Answer

Turn signals stop working when head lights are turned on or with out head lights turned on when you apply the brakes. i have already replaced all tail light bulbs with new sylvania 3057 bulbs,i have tried a new brake light switch at brake pedal.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

First remove all the signal bulbs both front and rear. Clean the sockets with electrical contact cleaner and replace the bulbs that you haven't changed yet. If still no solution replace the turn signal flasher. Lastly, if all else fails, check the wiring and the turn signal switch. Also this defect has happened when the headlight switch fails. Do the easiest things first. Good luck!

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

2 Answers

1989 Saab 900 turbo convertable


Either the ground wire is not working or disconnected or the wiring is short.

Jun 02, 2008 | 1998 Saab 900

2 Answers

1975 chevrolet truck. turn signals and stop light not working


Your brake lights go through your turn signal as well, That's what disables a brake light when you use your turn signal, In other words, When you hit your brakes, Your brake lights come on, Then when you use your turn signal, It cancels that brake light on the side that you're turning..Make sure you're getting fire to your turn signal switch and if it's coming through when you apply the brakes or use the signals..

Mar 10, 2015 | Chevrolet Cars & Trucks

1 Answer

Turn signal stop blinking when brakes applied


Chick ground at light fittings. Your turn lights are grounding through stop light bulbs

Dec 06, 2012 | 1982 Chevrolet G20

1 Answer

Brake lights 65 mustang stopped working.I wondered can the issue be in steering column


On a "one brake light bulb per side" setup,the brake switch feeds 12v to the turn/hazard switch,and the switch will apply 12v to both when no turn signal activated,the right only when the left signal is on,the left only when the right signal is on,and none when the hazards are on.With this in mind,it IS possible that the turn signal switch or wiring is the issue.If you are still running the original switch,try removing the switch and cleaning/regreasing the contacts(or look for something obviously worn or broken).If the switch is bad-hey,you got almost 50 years out of it! I'll bet you won't get that much longevity out of anything built now!
'

May 31, 2012 | Ford Mustang Cars & Trucks

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Is there an adjustment for the stop light switch on a 99 GMC Yukon. I have replace it and my brake lights still do not work. Park lights work fine.


There is no adjustment. The park lights are on a different circuit than the brake lights.
Do you have a third brake light that works. Its also on a different circuit but works from the same switch. Do your turn signals work. They use the same filament as the brake lights.
Also, the brake light circuit goes through the multi function (turn signal) switch.

Since the brake lights and turn signal lights use the same filament in the bulbs, the brake light circuit will pass through the turn signal switch. When a turn signal is used it cancels out the brake light for that side.

Let me know if your third brake light and turn signals work in the rear.
Also, if youy have not already, check/change the bulbs. The type of sockets those lights are in also get burned so look at them well.

Oct 18, 2011 | 1999 GMC Yukon

1 Answer

1998 honda accord, with the headlights on the tail lights are on but turn signals do not work. if head lights are off turn signals work unless i apply the brake, if i apply the brake the brake lights work...


It sounds as if you have a bad earth to either one or both of your rear light clusters. If it only happens when you indicate in one direction then that is the offending side.

Nov 20, 2010 | 1998 Honda Accord

1 Answer

2005 Canyon turn signal problem


No, but that's probably where your problem is. The wires get the hell beat out of them by stones, and then they short out and cause problems. I would take a look at it.

May 06, 2009 | 2005 GMC Canyon

1 Answer

Left rear turn signal and brake light dont work


You have a broken wire to the turn/brake light portion of the light as they use the same wire. Or where the plug goes into the light assy could be bad. Torsion mount lights are horrible and you should think about replacing with a universal light that you can wire direct.

Feb 17, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
2000 Honda Accord Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...