Question about 2002 Ford Taurus

Open Question

What fuse controls door chimes and keys - 2002 Ford Taurus

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
motor1258
  • 6674 Answers

SOURCE: 91 toyota camry door ajar light stays on along with the chime

Probably a faulty door switch. Are you familiar with what I'm talking about. Little push like switches that the doors push on as they close, usually on door post by latch end, or sometimes in jamb of door at hinge end.

Posted on Jan 25, 2009

Ad
fischmilch
  • 96 Answers

SOURCE: 1999 Saturn SL 2, The chime that indicates that

This is a common problem with the older saturns. The issue is in the key cylinder for the ignition. The way to fix it involves replacing the key cylinder, which in those cars is a total pain. It requires dismantling the steering column, drilling our the old lock, and replacing it with a new one. Problem is, it has to come from Saturn. There used to be a kit available from the dealer for about $120. I don't think it's available anymore. My wife's car has the same problem.

Posted on Mar 27, 2009

SOURCE: my door bell chime chimes all the time even if all

Pull the chime out.

Posted on May 26, 2010

  • 383 Answers

SOURCE: where is the fuse for the door ajar chime in a

there should be fuse that runs that but it not only thing on that fuse if u pull the fuse you lose cigar lighter radio dome light or what all on that circuit your best bet is to find the chime box should be under dash on drivers side just listen for the source once u find the box unplug it

Posted on Mar 06, 2011

  • 219 Answers

SOURCE: open door chimes and keys left in in car chimes

Door left open chime is operated by your interior light switch. It is located in a few places on different vehicles. Often in the door jam at the front or low down on the pillar at the rear of the door. You will notice a little black rubber boot and when you push it it goes in and out. That is your interior light switch.

Posted on Oct 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program New key switch 2000 oldsmobile silhouette


Key switch ? key fob ? Transmitter Programming ?
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.
Important: Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.
Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.
Perform the following steps in order to program the transmitter:
  1. Remove the ignition key from the ignition lock cylinder.
  2. Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
  3. Close all of the doors.
  4. Close the lift gate.
  5. Turn the ignition lock cylinder to ACC.
  6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
  7. Open and close any vehicle door.
  8. A chime will be heard when the system enters the BCM programming/diagnostic mode.
    Important: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
  9. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
  10. Repeat the previous step on each additional transmitter to be programmed.
  11. Remove the ignition key from the ignition lock cylinder.
  12. Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems.

Apr 22, 2016 | Oldsmobile Cars & Trucks

1 Answer

How do I program keyless entry on my 2002 grand prix? I have tried the way I found by removing mall pgm fuse n open door n turn key to acc. Doesnt work. The fob I have was for gp why it not work?


Important: All transmitters which are to be recognized by the remote control door lock transmitter (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.
  1. Remove the ignition key from the ignition lock cylinder.
  2. Close all of the doors.
  3. Remove the MALL PGM fuse from the fuse block.
  4. Insert the ignition key into the ignition lock cylinder.
  5. Turn the ignition to ACC.
  6. The body control module (BCM) will perform the following in order to identify the type of BCM installed in the vehicle:
    ?€¢
    Flash the seat belt indicator 1, 2, or 3 times.


    ?€¢
    Chime 1, 2, or 3 times.

  7. Turn the ignition to OFF, and then back to ACC within 1 second.
  8. The BCM may begin to chime and flash diagnostic trouble codes (DTCs). If the BCM has stored any DTCs, refer to Diagnostic System Check - Body Control System in Body Control System.
  9. Open and then close any vehicle door.
  10. The BCM will chime in order to confirm that the programming mode has been entered.
  11. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for approximately 14 seconds.
  12. Important: After approximately 7 seconds the BCM will chime once to confirm that synchronization has been completed. After approximately 14 seconds the BCM will chime a second time to confirm that the programming has been completed.
  13. Repeat the previous step in order to program each additional transmitter.
  14. Remove the ignition key from the ignition lock cylinder.
  15. Install the MALL PGM fuse into the fuse block.
  16. Operate the functions of each transmitter in order to verify correct system operation.

Jun 12, 2015 | 2002 Pontiac Grand Prix

1 Answer

Why won't my My 98 or 99 (sic)Ford Escort chime to indicate I left my lights on?


The warning chime sounds if the parking lamps (13200) or the headlamps (13008) are left on after the key has been removed from the ignition switch lock cylinder and either front door (20124) is opened. There is a chime module that controls this .
The safety belt warning chime (10D840) (also called the central processing unit or CPU) is an audible warning system and timing circuit. The system components include:
  • Timing circuit safety belt switch.
  • Dome lamp switches.
  • Safety belt warning indicator switch which is an integral part of the front safety belt buckle end (61203).
  • Ignition switch (11572).
  • Headlamp switch.
The warning chime sounds and the safety belt warning indicator illuminates when the ignition switch is placed in the ON position and the LH front safety belt is not buckled.
Key In Ignition Warning
The warning sounds if the key is left in the ignition switch lock cylinder when either door is opened and the ignition switch is in the LOCK or OFF position.
Don't any of chimes work ?
  • The Headlamp on Reminder Chime Is Inoperative/Does Not Operate Properly
  • Circuits.
  • Fuse junction panel.
  • Warning chime module.
  • GO to Pinpoint Test D .
Let me know ,mite work this out !
Don't

Apr 29, 2015 | Ford Escort Cars & Trucks

1 Answer

How to program a new alarm remote


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation .



Hope this helps, I found it online

-Scott

Feb 19, 2015 | 2004 Pontiac Grand Prix

2 Answers

The warning chime on my 2004 Jeep Grand Cherokee continues chiming when the door is closed and the key is in the first position from off. I tow this unit behind a motor home and need to leave the key in...


The chime is active because the sensor on one of the doors keeps reporting it as open - this is a defect in the sensor, located inside the actual lock. You cannot disable the chime, it's an integral part of the Body Control Module. To fix that the door will have to be dismantled and the sensor replaced, a job for a repair shop.
Until you reach one you can disconnect the battery and lock the doors manually.

May 17, 2011 | 2004 Jeep Grand Cherokee

1 Answer

Alreaddy did replace new batteries for key remote but the key remote is not working properly.. What cause is that?? do you know??


I know that this procedure work for Grand Prix and Monte Carlo, tesi it...

KEY FOB PROGRAMMING INSTRUCTIONS
Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:
Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.

Hope helps.

Jul 16, 2010 | 2001 Pontiac Grand Am SE

1 Answer

How do I reset a Key Fob for my 2006 Grand Prix. I have a key fob from a different year car that I would like to program to my current 2006 car. I only have one fob for the current car.


No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.

Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.
Perform the following steps: Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Nov 13, 2009 | 2006 Pontiac Grand Prix

1 Answer

How do you program the remotes for keyless entry with a 200 pontiac grand am?


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Oct 21, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Remote wont work


GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS 
Important 
Once the Keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver. 

Perform the following steps:
Sit in the vehicle driver's seat. (actually it’s much eazy er from the front pass seat) 
Remove the ignition key from the ignition lock cylinder. 
Close all of the vehicle's doors. 
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis. 
Turn the ignition lock cylinder to the ACC position. 
Turn the ignition lock cylinder OFF, then back to ACC within 1 second. 
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important 
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. 
Repeat step 8 in order to program each additional transmitter. 
Remove the ignition key from the ignition lock cylinder. 
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis. 
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation.

Good luck and hope this helps. 

Jun 17, 2009 | 2000 Pontiac Grand Prix

1 Answer

We purchased a 03 lincoln lsand need to reset the keyless entry


1. Sit in the vehicle driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all of the vehicle's doors.
4. Remove the MALL PGM fuse from the fuse panel. Or reset the fuse which controls your keyless remote.
5. Turn the ignition lock cylinder to the ACC position.
6. Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
7. Open and then close any vehicle door. You will hear a chime when the
remote control door lock receiver enters the programming/diagnostic mode. If
you do not hear a chime, start again at step 1.

This is an important fact here:

After 7 seconds, you may hear a chime confirming successful synchronization.
After approximately 14 seconds, you will hear a chime confirming successful
programming.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for
14 seconds.
9. Repeat step 8 in order to program each additional transmitter.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the MALL PGM fuse back into the fuse panel.

This is important as well:
Once the keyless entry receiver enters the programming/diagnostic mode, the
programming of the first transmitter erases all previous transmitter
programming information. You must then program all of the transmitters.
Program only 1 vehicle remote control door lock receiver at a time. If you
program multiple receivers simultaneously, the same transmitter could
possibly be programmed to more than 1 remote control door lock receiver

The fuse should be in your fuse block of your vehicle.

May 25, 2009 | 2003 Lincoln LS

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...