Question about 2000 Lincoln LS

1 Answer

What should the psi be on the fuel pump - 2000 Lincoln LS

Posted by on

1 Answer

30# to 55#

You should see 40-42#
at fuel rail valve

Posted on Mar 12, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fuel pump seems to be pumping gas but my van wont start 02 chevy venture cranks gets fire an gas but wont start


Just because it pumps gas doesn't mean it is at the exact pressure it should be? Most fuel pumps have a psi of 40 to 45 psi, your fuel pump could be pumping at 25 psi or less which is not enough to start your car even though you can see some fuel pumping out. A simple tool to check fuel pressure can be bought at any auto parts store, check the specs on the fuel pump for your 02 Chevy first to see at what pressure it works, then use the fuel pressure gauge to check it. Anything less than what the specs on your fuel pump are suppose to be and you have a bad fuel pump?

Let's say your fuel pump works at 43psi, you hook up the fuel pressure gauge and you find that it reads 25 to 30 psi, that means it's not enough fuel pressure to start your engine.

Jun 07, 2015 | 2002 Chevrolet Venture

3 Answers

Fuel pump pressure on 1969 small block camaro


6-8 psi, usually will give 60-80 gph (gallons per hour)

Feb 03, 2015 | 1969 Chevrolet Camaro

2 Answers

Fuel pressure 1998 jeep grand cherokee 4.0 L V6


You should have a test port on the Fuel Supply rail, use a tool from a local auto parts "Tool Loaner program" where you can borrow tools for free,w/a deposit of course,then follow the steps provided;

MPI Fuel System Pressure Test

The MPI fuel system used in vehicles equipped with a 4.OL engine employs a vacuum balanced pressure regulator. Fuel pressure should be approximately 55-69 kPa (8-10 psi) lower with the vacuum line attached to the regulator than with the vacuum line disconnected. System fuel should be 214 kPa (31 psi) with the vacuum line connected to the regulator and 269 kPa (39 psi) with the vacuum line disconnected. CAUTION: Some fuel may be discharged when connecting fuel gauge to fuel rail.
  1. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to test port pressure fitting on fuel rail (Fig. 7).
  2. Remove vacuum line from pressure regulator.
  3. Start the vehicle.
  4. Note gauge reading. With vacuum line disconnected, fuel pressure should be approximately 269 kPa (39 psi).
  5. Connect vacuum line to pressure regulator. Note gauge reading. Fuel pressure should be approximately 214 kPa (31 psi).
  6. If fuel pressure is not approximately 55-69 kPa (8-10 psi) higher with vacuum line removed from regulator, inspect pressure regulator vacuum line for leaks, kinks or blockage. CAUTION: Fuel pressure will rise to as much as 655 kPa (95 psi) when the fuel return tine is pinched shut, shut engine down immediately after pinching oft fuel return line.
  7. If fuel pressure is low, momentarily pinch shut the hose section of the fuel return line. If fuel pressure remains low, inspect the fuel supply line, fuel filter, and fuel rail inlet for blockage. If fuel pressure rises replace fuel pressure regulator.
  8. If fuel pressure is above specifications, inspect the fuel return line for kinks and blockage.

Capacity Test

  1. Remove the cap from the pressure test port in the fuel rail.
  2. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to the pressure fitting on the fuel rail (Fig. 7).
  3. Start the vehicle. Pressure should be approxi- mately 214 kPa (31 psi) with the vacuum hose connected to the pressure regulator and 269 kPa (39 psi) with the vacuum hose removed from the pressure regulator.
  4. If the pressure is not to specification, check the following before replacing the fuel pressure regulator:
  • 4a - Inspect the fuel supply and return lines/hoses for kinks or restricting bends
  • 4b - Check the fuel pump flow rate. A good fuel pump will deliver at least 1 liter of fuel per minute with the fuel return line pinched off. If the fuel pump does not pump adequately, then inspect the fuel system for a plugged fuel filter or fuel pump inlet filter (sock). Fuel pump flow rate can be done by connecting one end of an old A/C gauge hose to the fuel test port on the fuel rail and inserting the other end of the hose into a container of at least 1 liter capacity. Run the fuel pump by installing a jumper wire into diagnostic connector terminals D1-5 and D1-6. Be sure to pinch off the fuel return line or most of the fuel will be returned to the fuel tank.

May 19, 2014 | 1996 Jeep Grand Cherokee

1 Answer

Dodge2500two new fuel pumps will not prime up


Definitely start w electrical, go to fuel psi at proper locations & make sure PSI is not bleeding down after ignition is off If so you found the main problem. Now find out where it's losing PSI to. (leak, regulator, injector etc )

May 05, 2014 | 2000 Dodge Ram Maxi

1 Answer

Fuel pressure


FUEL PRESSURE Command the fuel pump ON with a scan tool.Observe the fuel pressure gage with the fuel pump commanded ON.VIN Z335-375 (48-54 psi)Except VIN Z385-425 kPa (55-62 psi)

Nov 11, 2013 | 2003 GMC Yukon XL

1 Answer

Fuel pump without enough psi. suggestions??


I am sorry to say that if the old pump was putting out 40psi then the pressure switch will need the same psi from the new pump.
With the psi les then what the computer knows the engine needs it will not allow it to start and run.

Jan 19, 2012 | Cars & Trucks

1 Answer

Fuel pressure intermittently drops causing sputter and die.


check for 12v constant at your fuel pump if you are not getting that replace your relay.
if you are getting 12 volts at your fuel pump the fuel pump is possible to run tuel it gets warm then shut down to a lower rpm I would then replace the fuel pump

Oct 10, 2009 | 1994 Dodge Ram

2 Answers

FUEL PUMP MAKES NOISE PRESSURE GAGE READS 40 PSI ENGINE BEGINS TO SPUTTER MY PRESSURE GAGE DROPS TO ABOUT 20 PSI


Fuel pump is bad. At idle pressure should read 50 PSI. Replace with original manufacture fuel pump after market pumps will burn out fast and are unreliable from my experience. Also could have a bad fuel regulator but that only works while driving down the road full throttle. You can unhook the fuel rail pressure regulator and that will give it full fuel and the pressure reading should read 60 PSI while it is running. If you turn the engine off and turn the key to run position it should read 50 PSI and hold for 60 seconds, if it drops below 30 PSI after 30 seconds Pump is defective. Many pumps are going bad here of late as people have been running them less than ¼ tank and this kills the pump. The fuel cools and lubricates the pump so the lower the fuel level the worse it is on the pump below ¼ tank. Not to hard of a job to do if you want instructions let me know.

Sep 28, 2009 | 1997 Chevrolet Lumina

Not finding what you are looking for?
2000 Lincoln LS Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...