Question about 2000 Mercury Mystique

1 Answer

Where is the ecm and the dtc fuse - 2000 Mercury Mystique

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 76,673 Answers

It is on the pass. side under the hood at the firewall. See diagram below.

where is the ecm and the dtc fuse - emissionwiz_55.gif What are you referring to on the "dtc" fuse, if the check engine light doesn't come on then the cigar lighter fuse is burned out.

Posted on Mar 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse that works the oil pressure gauge and the battery gauge for a 2005 chevy trailblazer


NO , there is not a fuse just for those two thing's ! There are two power supply's for the whole insturment cluster . You could need a new cluster or the ECM isn't sending this info. to the cluster . Could have DTC'S - diagnostic trouble codes stored in the PCM or the insturment cluster . Without knowing how this works (insturment cluster gets it's info.) Your best bet , take it to a qualified repair shop that has the knowledge and test equipment to diagnose this problem.
Engine Oil Pressure Gage
The instrument panel cluster (IPC) displays the engine oil pressure as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the engine oil pressure. The engine oil pressure gage defaults to 0 psi (0 kPa) or below if:
• The ECM detects a malfunction in the engine oil pressure sensor circuit.
• The IPC detects a loss of serial data communications with the ECM.
For the 4.2L LL8, the ECM uses an engine oil switch that is open when the oil pressure is normal and closed when the oil pressure is low. At normal pressure, the engine oil pressure gage will display 275 kPa (40 psi). At low pressure, the gage will go to 0 kPa and the low pressure warning will be displayed in the driver information center (DIC). At high pressure, the gage will display 551 kPa (80 psi). Any values between these three values are calculated values determined by the ECM.

Voltmeter
The instrument panel cluster (IPC) displays the vehicle voltage based on the information from the body control module (BCM). The IPC uses the serial data information from the BCM to provide a voltage level indication on the voltmeter.

DTC P0521: Engine Oil Pressure (EOP) Sensor Performance

DTC P0522 Engine Oil Pressure (EOP) Sensor Circuit Low Voltage
DTC P0523 Engine Oil Pressure (EOP) Sensor Circuit High Voltage

Volt Gage Inaccurate or Inoperative
2
Install a scan tool.
Turn the ignition ON, with the engine OFF.
With the scan tool, perform the instrument panel cluster (IPC) gauges output control.
Does the volt gauge move up and down when commanded?

Aug 12, 2017 | Cars & Trucks

1 Answer

2003 saturn L300 p1780


DTC P1780 (3.0L (L81))

To improve shift feel, the transmission control module (TCM) may request that the engine control module (ECM) reduce engine torque during shift events. When such a request is received, the ECM responds by retarding the base ignition timing and notifying the TCM that the request has succeeded. If the ECM is unable to comply with the request, the ECM sends the TCM a message that the request has failed.
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM. A fault in the CAN will not cause DTC P1780 to set by itself. If a CAN fault occurs, other DTCs will set before DTC P1780.
When the TCM receives a torque reduction failure message from the ECM, then DTC P1780 will set. DTC P1780 is a type C DTC. Take your pick of which you think this code is for , this or the TSB - technical service bulletin. What need to hook up scan tool an data PID'S - Do you know what PID'S are ? sensor data read on a scan tool .

Mar 04, 2016 | 2003 Saturn L-Series

1 Answer

Where is the ECM relay and fuse, I have a DTC P0690 code I am trying to correct


code p 0690 refers to ECM power relay control--sense circuit high====causes wiring short to positive--ECM relay---ECM The ECM relay will be in the collection of relays next to the battery

Dec 26, 2015 | 2008 Chevrolet Silverado 1500 2WD

2 Answers

Bought car at auction- no keys. Had key made at GM dealer. Programmed key- key works. Car wont start- Codes are P0633 and P1629. cannot clear codes


DTC P0633 : Theft Deterrent Key Not Programmed

When learning the pre-release password, as well as the challenge and response sequence, the engine control module (ECM) is placed in learn mode. DTC P0633 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the password and challenge/response are learned, learn mode will be exited when the engine is successfully started. At this point, the DTC will be cleared. If the ECM does not exit learn mode, P0633 will remain current and indicate a fault.
The "key" referenced in the DTC descriptor does not refer to the vehicle key. In this case, "key" is referring to the challenge response.
DTC P0633 requires a successful engine start to exit the learn procedure and clear the DTC. If an unrelated malfunction exists that causes engine starting to be disabled or otherwise unavailable, learn mode will not exit and DTC P0633 will remain current. In this situation, the cause of the inoperative engine starting must be corrected before diagnosing DTC P0633.
DTC P1629: Theft Deterrent Fuel Enable Signal Not Received
The theft deterrent module (TDM) sends the pre-release password to the engine control module (ECM) via the serial data circuit. The ECM then sends a challenge to the TDM. Both the ECM and TDM perform a calculation on this challenge. If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting.
DTC P1629 is an indicator that the challenge response was not received within the required 2 second window. This does not necessarily indicate a fault is present with the TDM or ECM. Factors such as a long engine crank, a delay in the serial data communication, or B-codes set in the TDM will cause DTC P1629 to set. This DTC should not be used as a fault indicator, but rather as a symptom to assist in the diagnosis of these other systems.
Who checked the codes , you -dealer ? You need to have BCM checked for codes B - codes ! you need a up scale diagnostic scan tool for that , dealer Tech -2 !
DTC B3935 57 : Transponder Authentication Error
DTC B3976 46 : Unconfigured Transponder/Vehicle Configuration Not Programmed
DTC B3060 : Unprogrammed Transponder Identification Code Received
DTC B3055: No Transponder Modulation or No Transponder
DTC B3031: Security System Controller In Learn Mode

Aug 07, 2015 | 2006 Buick Lucerne

1 Answer

P2176, 1682, 0443 on a 2005 envoy V8. Stalls and won't restart until it cools down


DTC P2176 Minimum Throttle Position Not Learned
Circuit Description
The commanded throttle position is compared to the actual throttle position based on accelerator pedal position and possibly other limiting factors. Both values should be within a calibrated range of each other. The engine control module (ECM) continuously monitors the commanded and actual throttle positions. This DTC sets if the values are greater than the calibrated range.
DTC P1682 Ignition 1 Switch Circuit 2
The ignition 1 voltage circuit supplied by the powertrain ignition 1 relay is used to power the electronic throttle control (ETC) circuitry internal to the engine control module (ECM). The second ignition 1 voltage circuit is supplied by the ignition switch through the ECM 1 fuse, and is used to power the remaining internal ECM circuits. If the ECM detects a voltage difference between the two ignition 1 voltage circuits, DTC P1682 will set.
DTC P0443 Evaporative Emission (EVAP) Purge Solenoid Control Circuit
An ignition voltage is supplied directly to the evaporative emission (EVAP) canister purge solenoid valve. The EVAP canister purge solenoid valve is pulse width modulated (PWM). The scan tool displays the amount of ON time as a percentage. The control module monitors the status of the driver. The control module controls the EVAP canister purge solenoid valve ON time by grounding the control circuit via an internal switch called a driver. If the control module detects an incorrect voltage for the commanded state of the driver, this DTC sets.
You have electrical problems of some kind , with out doing some testing with a scan tool an volt meter .Hard to say ! could even be the PCM shorting out after getting hot ! I have seen this happen a few times before !

May 05, 2015 | Cars & Trucks

1 Answer

Can the Body Module on 2001 Impala cause door locks, trunk lock and interior lights not to work?


ECM has nothing to do those thing's . Probably not A BCM problem either . Did the Garage check for DTC'S - diagnostic trouble code's ?
DTC B3064 or B3069
DTC B3127
DTC B3128, B3133, or B3138
DTC B3132
DTC B3137
DTC B3272

Did they test the electrical circuit's for these componets ? Looking at a wirng diagram to see what if anything these have in common ,power feed , ground etc. maybe . What kind of garage did you take it to . Just to let you know ,replacing any module on your vehicle would need programming , dealer .

Oct 26, 2017 | 2001 Chevrolet Impala

1 Answer

Had p code 1167 b1 s1 on and off for a couple of days, now ihave misfire code for cylinders 2 4 6 and running very poor as you would know checked plugs and wires ( ok ) ignition wires are mixed on the...


This has nothing to do with the O2 sensor, this is the A/F sensor in the exhaust manifold

DTC P1167: A/F Sensor (Sensor 1) Heater System Malfunction

NOTE: If DTC P1162 is stored at the same time as DTC P1167, troubleshoot DTC P1162 first, then troubleshoot DTC P1167.

Reset the ECM/PCM.
Start the engine. Wait for at least 80 seconds . Is DTC P01167 indicated? YES - Go to step 3. NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at C102 (located under the under-hood fuse/relay box), the A/F Sensor relay, the A/F Sensor (Sensor 1), and the ECM/PCM.
Disconnect the A/F Sensor 4P connector, and ECM/PCM connector C (31P).

Connect ECM/PCM connector terminals C14 and C15 to body ground with a jumper wire.

Check for continuity between A/F Sensor (Sensor 1) 4P connector terminal No.1, No.2, and body ground individuality. Is there continuity? YES - Replace the A/F Sensor (Sensor 1). NO - Repair open or short in the wire between the A/F Sensor (Sensor 1) and the ECM/PCM (C14 or C15).

Oct 08, 2011 | Cars & Trucks

1 Answer

What does the code p1166 mean on my 2003 rsx type s


DTC P1166: A/F Sensor (Sensor 1) Heater Circuit Malfunction


  1. Reset the ECM/PCM.
  2. Start the engine.
Is DTC P1166 indicated?

YES - Go to step 3.

NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at C101 (located under the right side of the dash), C401 (located under the left side of the dash), C402 (located under under the left side of the dash) the A/F Sensor relay, the A/F Sensor (Sensor 1) and the ECM/PCM.


  1. Check the following fuse:
    • No.14 OPTION (30A) fuse in under-hood fuse/relay box.
    • No.2+B LAF HEATER (20A) fuse in under-dash fuse/relay box.
    • No. 4ACG (10A) in under-dash fuse/relay box.
Are any of the fuses blown?

YES - Repair short in the wire between the A/F Sensor relay and the fuses.

NO - Go to step 4.

94729647

  1. Measure voltage between ECM/PCM connector terminals A1 and A24, 30 seconds after the ignition switch is turned ON (II).
Is there battery voltage?

YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.

NO - Go to step 5.

94729648

  1. Measure voltage between ECM/PCM connector terminals A22 and A24.
Is there battery voltage?

YES - Go to step 6.

NO - Go to step 10.


  1. Turn the ignition switch OFF.
  2. Disconnect ECM/PCM connector E (31P).
  3. Turn the ignition switch ON (II).
94729649

  1. Connect ECM/PCM connector terminal E8 to body ground with a jumper wire, then measure voltage between ECM/PCM connector terminals A1 and A24.
Is there battery voltage?

YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.

NO - Repair open or short in the wire between the A/F Sensor (Sensor 1) and ECM/PCM (A1).


  1. Turn the ignition switch OFF.
  2. Disconnect the ECM/PCM connector A (31P) and the A/F Sensor (Sensor 1) 4P connector.
94729650

  1. Check for continuity between the A/F Sensor (Sensor 1) 4P connector terminal No.3 and body ground.
Is there continuity?

YES - Repair short in the wire between the A/F Sensor relay, A/F Sensor (Sensor 1) and ECM/PCM (A22).

NO - Go to step 13.


  1. Turn the ignition switch ON (II).
94729651

  1. Measure voltage between ECM/PCM connector terminals E8 and A24.
Is there battery voltage?

YES - Repair open in the wire between the ECM/PCM (A22) and the A/F Sensor (Sensor 1).

NO - Go to step 15.


  1. Check for continuity in the wires between the A/F Sensor and the fuses.
Is there continuity?

YES - The wires are OK. Replace the A/F Sensor relay.

NO Repair open in the wire between the A/F Sensor relay and the fuses.

Mar 17, 2011 | Acura RSX Cars & Trucks

2 Answers

P0031, ho25circuit low, bank 1 sensor 1. sft b1 -3.91, ltft b1 .78, stft b2 -3.91, ltft b2 3.91. R&R ox sensor or what


Hello,
P0031 - Bank 1 Heated Oxygen Sensor No. 1 Heater Circuit - Low Voltage. That is what this code means.
DTC P0031 is set when Bank 1 HO2S No.1 heater current is less then .09 amps, or potential difference between heater positive and negative terminals is more then 13.99 volts while HO2S heater is on. MIL (The engine light) is illuminated when Engine Control Module (ECM) detects malfunction during 2 consecutive drive cycles.
Possible Causes are: - Bank 1 HO2S No. 1 heater circuit malfunction - Bank 1 HO2S No. 1 heater malfunction - ECM malfunction - HO2S heater relay

DTC Confirmation Test (Advanced/Intermediate Users): Ensure intake air tempature is 18f (-8c) or more, engine coolant tempature is 18-230f (-8-110c) and vehicle is at an altitude of 8000 feet or below, and barometric pressure is 75 kPa or more. Turn ignition off, connect scan tool and turn ignotion on. Using scan tool, clear DTCs. Start engine and run at idle speed for 5 minutes. Using scan tool check for current or pending DTC P0031.

Diagnosis & Repair Procedure (Advanced/Intermediate Users): 1. If engine system check has been performed, go to the next step. If engine system check has not been performed, do the system check.
2. Turn ignition off. Disconnect Bank 1 HO2S No. 1 4-pin harness connector. Bank 1 HO2S No. 1 is located in the left exhause pipe before catalytic convertor. Measure resistance between Bank 1 HO2S No. 1 pigtail connector terminal No. 3 (Green wire) and No. 4 (Blue wire). Resistance should be 5.0-6.4 ohms at 68f (20c). If resistance is as specified, go to next step. If resistence is not as specified, replace HO2S. After repair repeat DTC Confirmation Test (Above).
3. Disconnect HO2S heater relay. HO2S heater relay is located on the left fender well. Turn ignition On. Measure voltage between ground and HO2S heater relay socket cavity No. 3 (Black/White wire). Also measure voltage between ground and HO2S heater relay socket cavity No. 1 (Blue/White wire). If voltage readings at both measurements is 10-14 voltes, go to step 5. If voltage readings are not as specified go to next step.
4. Check for blown HO2S (15-amp) or IG COIL (20-amp) fuses. Fufses are located in the underhood fuse and relay boxc. If fuses are okay, check for open or short it to ground in Black/White wire between IG COIL fuse HO2S heater relay. If problem is found repair as necessary. After repair repeat DTC Confirmation Test (Above).
5. Turn Ignition off. Install HO2S heater relay. Dicsonnect ECM 30-pin harness connector C51-2. ECM is located under instrument panel, under glove box. Measure voltage between ground and ECM harness connector C51-2 terminal No. 4 (Green wire). If voltage reading is 10-14 volts, subsitute a known-good ECM, and repeat DTC Confirmation Test (Above). If DTC does not reset, testing is complete. If voltage readings are not specified, go to next step.
6. Check for short to ground in Green wire between Bank 1 HO2S No. 1 and ECM. If no problem with wiring is found, replace HO2S heater relay. If problem persists after repairs, subsitute a known-good ECM and repeat DTC Confirmation Test (Above).

I hope this helps and is what your looking for. Best of luck.

Nov 21, 2009 | 2003 Suzuki XL-7

1 Answer

Vw passat 2000 1.8t front wheel drive


please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo

Jun 21, 2008 | 2000 Volkswagen Passat 4Motion

Not finding what you are looking for?
2000 Mercury Mystique Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...